Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

38-116
#8

Thanks for that. I may keep my eye out for one as painting the lines would be difficult, as you suggested. I suspected that someone got over zealous with polishing compound. I found quite a bit of residue in the joint between the glass and bezel. I suspect they took some paint off and decided to do the whole thing as the only paint I could find was on the very edges. Looking at the lines of the grille cloth, it appears that they tried to line up the pastern in the small grills with the large grill. Am I correct? Also, the "High Fidelity" on yours is in script. Mine was the same as the 37-116 so that's the decal I put on it. They must have used what they had on hand!


Messages In This Thread
38-116 - by rfeenstra - 11-19-2019, 12:19 AM
RE: 38-116 - by wardmc1 - 11-19-2019, 07:43 AM
RE: 38-116 - by rfeenstra - 11-19-2019, 08:07 AM
RE: 38-116 - by wardmc1 - 11-19-2019, 09:26 AM
RE: 38-116 - by rfeenstra - 11-19-2019, 05:24 PM
RE: 38-116 - by rfeenstra - 11-19-2019, 09:35 PM
RE: 38-116 - by wardmc1 - 11-20-2019, 07:41 AM
RE: 38-116 - by rfeenstra - 11-20-2019, 06:53 PM
RE: 38-116 - by wardmc1 - 11-21-2019, 06:56 AM
RE: 38-116 - by rfeenstra - 11-21-2019, 10:44 AM
RE: 38-116 - by Ron Ramirez - 11-21-2019, 12:15 PM
RE: 38-116 - by rfeenstra - 11-21-2019, 01:02 PM
RE: 38-116 - by wardmc1 - 11-22-2019, 07:19 AM
RE: 38-116 - by rfeenstra - 11-22-2019, 11:17 PM
RE: 38-116 - by wardmc1 - 11-23-2019, 02:09 AM
RE: 38-116 - by rfeenstra - 12-16-2019, 11:25 PM
RE: 38-116 - by Phlogiston - 12-17-2019, 10:09 AM
RE: 38-116 - by rfeenstra - 12-17-2019, 12:13 PM
RE: 38-116 - by fenbach - 12-17-2019, 06:49 PM
RE: 38-116 - by mikethedruid - 12-17-2019, 07:51 PM
RE: 38-116 - by rfeenstra - 12-17-2019, 09:15 PM
RE: 38-116 - by Phlogiston - 12-17-2019, 09:28 PM
RE: 38-116 - by rfeenstra - 12-17-2019, 11:05 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Samlex heavy-Duty bench supply filter question
Hello Everyone, I have one of my Heavy-duty bench powersuplies made by Samlex it's 13.8 volt dc 20-25 amp supply. What I...radiorich — 11:24 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
It's a Glaser Sears changer which Philco's engineers thought was an upgrade over a VM, but in retrospect I'd prefer the ...jeibner — 10:39 PM
AC/DC Transformer-less Sets
Joseph, Thank you for the confirmation. I knew that there must be more to the Transformer-less AC/DC radios than the ...PeterN — 10:30 PM
AC/DC Transformer-less Sets
Good evening, folks. Power station engineer here! The east coast had pockets of DC-only power well into the twentieth...jrblasde — 10:11 PM
AC/DC Transformer-less Sets
Model 40 does not have a rectifier, so it would be a DC only model. This however does not say anything about using...morzh — 08:01 PM
AC/DC Transformer-less Sets
I was wondering if anyone knows if these AC/DC transformer-less sets were actually used on 110v DC anywhere, and when. ...PeterN — 06:35 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
Given the 1960s vintage, it is likely that the cartridge is ceramic, likely more stable. The changer looks like a Voice...MrFixr55 — 05:03 PM
Jackson 665 j2 schematic request
FIXED!daveone23 — 03:55 PM
Bakelite crack repair - what is best epoxy?
Thanks everyone. I appreciate you sharing your experience and looks like I'll work with the 24 hr two part clear epoxy....de371 — 10:25 PM
Jackson 665 j2 schematic request
Without a schematic its going to be hard tracing the wire wound spool resistors.daveone23 — 05:21 PM

[-]
Who's Online
There are currently no members online.

>