Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

General Electric 202 revived.
#7

There is a good deal of room in this set and the bulb sits back from the dial which is glass painted with numbers, these numbers on the glass will wipe off in[Image: http://blogs.creighton.edu/cjw84423/file...GP6314.jpg] a blink, you cannot be too careful if you want them to survive, I cannot stress this enough. If you went with the LEDs you would likely never need to replace them. Got pic from Chris Wilmes.

Pablo

Tubetalk1


Messages In This Thread
General Electric 202 revived. - by Jayce - 11-30-2019, 09:21 PM
RE: General Electric 202 revived. - by David - 12-01-2019, 09:11 PM
RE: General Electric 202 revived. - by David - 12-01-2019, 09:58 PM
RE: General Electric 202 revived. - by Paul Philco322 - 12-01-2019, 10:20 PM
RE: General Electric 202 revived. - by Jayce - 12-01-2019, 11:38 PM
RE: General Electric 202 revived. - by Jayce - 12-03-2019, 12:20 AM
RE: General Electric 202 revived. - by jake wells - 12-03-2019, 12:27 AM
RE: General Electric 202 revived. - by Jayce - 12-03-2019, 03:03 PM
RE: General Electric 202 revived. - by 462ron - 12-04-2019, 09:01 AM
RE: General Electric 202 revived. - by rfeenstra - 12-04-2019, 09:39 AM
RE: General Electric 202 revived. - by Jayce - 12-04-2019, 06:21 PM
RE: General Electric 202 revived. - by jake wells - 12-04-2019, 06:51 PM
RE: General Electric 202 revived. - by jake wells - 12-04-2019, 09:09 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Need to purchase some accessories for restoration of my Old Philco Radio
Hi Paulo, Welcome to the Philco Phorum. I can see why you want to find good reproduction parts. That is a bea...MrFixr55 — 11:10 PM
HiFi (Chifi) tube amp build - but my own design.
Tim, I have some bakelite sockets in my work shop that I can dig up. I believe quite a few are NOS. I will take photo...RodB — 10:03 PM
Philco 610B oscillator wiring
> The cathode as noted is wired directly to the ground side of the heater filament for that tube, not to the #17 and ...Radioroslyn — 08:12 PM
HiFi (Chifi) tube amp build - but my own design.
Tim; I noticed your post a little late, but I would take one of the junk sockets and try to break a chunk out of it wi...Arran — 08:07 PM
Need to purchase some accessories for restoration of my Old Philco Radio
Here is a list of resources found in our online library that you might find useful. Mike's Gobs of Knobs email addres...klondike98 — 01:46 PM
First Radio restoration
Hi Tubeman, Welcome to the Philco Phorum.  Phamily Phriendly Pfun with Phine Pholks Phull of Philco Phacts. (See a p...MrFixr55 — 12:33 PM
First Radio restoration
You could post in the WANTED ADs section here on the Phorum and see if anyone has an RF generator that they want to sell...klondike98 — 11:55 AM
Zenith H725
Good ideas, thank you Arrange and Rich. I have the adhesive aluminum foil already and can try that immediately. More ...EdHolland — 10:18 AM
Graphics for majestic 1050 dial glass.
Murf; I found this thread on the ARF, the first photo has a pretty good view of the dial glass. Regards ArranArran — 01:12 AM
Zenith H725
hello Ed, how about that speacial tape used for ducting it's like foil or how about thin piece of aluminum roof flash...radiorich — 12:19 AM

[-]
Who's Online
There are currently 1448 online users. [Complete List]
» 2 Member(s) | 1446 Guest(s)
AvatarAvatar

>