40-180 Output Transformer

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

40-180 Output Transformer

Tucker
Junior Member

Posts: 46
Threads: 15
Joined: Jun 2017
City: Madison, WI

12-08-2019, 03:43 PM

Well, I just looked at the 4 wires under the existing output transformer and they are ;

Black - goes to pin 2 of a 41 tube

Tan - goes to pin 2 of the other 41 tube

Black/Tan striped - goes to a terminal strip lug that splits off to pin 2 of the 7C6 tube and pin 3 of one of the 41 tubes and it also connects to one of the filter caps.

Bare wire - goes directly to the speaker.

I'm wondering if I wouldn't use the red wire for this radio ?

(This post was last modified: 12-08-2019, 09:58 PM by Tucker.)

Find

« Next Oldest | Next Newest »

Messages In This Thread

40-180 Output Transformer - by Tucker - 12-07-2019, 09:10 PM

RE: 40-180 Output Transformer - by Forrest - 12-07-2019, 10:18 PM

RE: 40-180 Output Transformer - by Tucker - 12-08-2019, 03:43 PM

RE: 40-180 Output Transformer - by Radioroslyn - 12-08-2019, 03:52 PM

RE: 40-180 Output Transformer - by Tucker - 12-08-2019, 10:03 PM

RE: 40-180 Output Transformer - by Forrest - 12-09-2019, 08:35 AM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic. This radio had a 8" Zenith speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM

Who's Online

There are currently 4557 online users. [Complete List]
» 1 Member(s) | 4556 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me