Philco 49-901 restoration

Thread Rating:

Bob Andersen
Phorum Expert

Posts: 797
Threads: 42
Joined: Dec 2008
City: Chicago, IL

#15

12-10-2019, 05:46 PM

I recently finally got around to finishing this radio Icon_biggrin

After repairing all the damage, I stripped off the paint with over cleaner, hot water and a brass wire brush.
[Image: https://live.staticflickr.com/7852/46639...f40a_c.jpg]

[Image: https://live.staticflickr.com/65535/4903...e790_c.jpg]

Next up, Krylon white primer and Bondo glazing compound for any remaining small defects.
[Image: https://live.staticflickr.com/65535/4903...b834_c.jpg]

Then, Krylon Ivy Green paint plus Dupli-Color GOld for the grille and artist water based acrylic for the pinstripes and recessed lettering.
[Image: https://live.staticflickr.com/65535/4907...cc24_c.jpg]

[Image: https://live.staticflickr.com/65535/4912...f83a_c.jpg]

[Image: https://live.staticflickr.com/65535/4912...0fe6_c.jpg]

As for the damaged control drum, I attached a metal collar with set screws to the body with four small screws. There was just enough room for it to fit inside without rubbing.
[Image: https://live.staticflickr.com/65535/4912...cb74_c.jpg]

[Image: https://live.staticflickr.com/65535/4912...c68b_c.jpg]

[Image: https://live.staticflickr.com/65535/4912...f644_c.jpg]

The only remaining item is the preset jewel indicator. It's quite dim and I left it off while I ponder what to do about it. Apparently because I'm missing a light pipe that can be seen in this example.

[Image: https://live.staticflickr.com/65535/4920...3f8d_o.jpg]

« Next Oldest | Next Newest »

Messages In This Thread

RE: Philco 49-901 restoration - by Bob Andersen - 12-10-2019, 05:46 PM

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic. This radio had a 8" Zenith speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM

Who's Online

There are currently 4898 online users. [Complete List]
» 2 Member(s) | 4896 Guest(s)