1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
BAKELITE BLOCK TYPE capacitors
Kestas
Member
***
Posts: 177
Threads: 19
Joined: Feb 2014
City: The Motor City,Detroit MI
#8

01-01-2020, 09:29 PM
These .00011 mf capacitors also fooled me on the first Philco I restored. I thought they were mica until someone pointed out they were paper capacitors.
Find
« Next Oldest | Next Newest »


Messages In This Thread
BAKELITE BLOCK TYPE capacitors - by fenbach - 12-31-2019, 08:51 PM
RE: BAKELITE BLOCK TYPE capacitors - by radiodale - 12-31-2019, 10:43 PM
RE: BAKELITE BLOCK TYPE capacitors - by morzh - 01-01-2020, 02:27 PM
RE: BAKELITE BLOCK TYPE capacitors - by Kestas - 01-01-2020, 09:29 PM
RE: BAKELITE BLOCK TYPE capacitors - by morzh - 01-02-2020, 10:58 AM
RE: BAKELITE BLOCK TYPE capacitors - by fenbach - 01-04-2020, 02:11 PM
RE: BAKELITE BLOCK TYPE capacitors - by morzh - 01-04-2020, 08:59 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM

[-]
Who's Online
There are currently 3799 online users. [Complete List]
» 1 Member(s) | 3798 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration