38-116 Restoration

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

38-116 Restoration

rfeenstra
Phorum Expert

Posts: 1,190
Threads: 50
Joined: Oct 2017
City: Allendale, MI

01-02-2020, 01:39 AM

RF sub chassis complete. Tubular capacitors stuffed, coils checked, and most resistors replaced. I didn't want to have to get into this unit again to chase down a noisy resistor so I just changed them. All coils checked out fine. I don't know if the 38-116 has the same common issue with the oscillator coil for band 2 but it appeared to be fine and measured good. According to the part numbers, it is a different coil and it looks different so I think I'm good.

Find

« Next Oldest | Next Newest »

Messages In This Thread

38-116 Restoration - by rfeenstra - 12-30-2019, 09:10 PM

RE: 38-116 Restoration - by rfeenstra - 12-30-2019, 11:46 PM

RE: 38-116 Restoration - by rfeenstra - 01-02-2020, 01:39 AM

RE: 38-116 Restoration - by rfeenstra - 01-04-2020, 04:33 PM

RE: 38-116 Restoration - by KCMike - 01-04-2020, 05:46 PM

RE: 38-116 Restoration - by rfeenstra - 01-04-2020, 07:03 PM

RE: 38-116 Restoration - by rfeenstra - 01-04-2020, 08:08 PM

RE: 38-116 Restoration - by rfeenstra - 01-04-2020, 08:49 PM

RE: 38-116 Restoration - by rfeenstra - 01-07-2020, 12:13 AM

RE: 38-116 Restoration - by rfeenstra - 01-08-2020, 08:35 PM

RE: 38-116 Restoration - by rfeenstra - 01-09-2020, 11:47 PM

RE: 38-116 Restoration - by KCMike - 01-10-2020, 09:55 AM

RE: 38-116 Restoration - by rfeenstra - 01-13-2020, 03:12 AM

RE: 38-116 Restoration - by morzh - 01-13-2020, 08:47 AM

RE: 38-116 Restoration - by Nathan Slingerland - 01-13-2020, 11:55 AM

RE: 38-116 Restoration - by rfeenstra - 01-17-2020, 12:10 AM

RE: 38-116 Restoration - by rfeenstra - 01-17-2020, 12:14 AM

RE: 38-116 Restoration - by Jake Blake - 01-17-2020, 09:38 AM

RE: 38-116 Restoration - by rfeenstra - 01-21-2020, 03:35 PM

RE: 38-116 Restoration - by mikethedruid - 01-21-2020, 05:49 PM

RE: 38-116 Restoration - by rfeenstra - 01-21-2020, 06:22 PM

RE: 38-116 Restoration - by Nicko - 02-02-2020, 09:51 PM

RE: 38-116 Restoration - by klondike98 - 02-02-2020, 10:21 PM

RE: 38-116 Restoration - by rfeenstra - 02-16-2020, 03:25 PM

RE: 38-116 Restoration - by quick573 - 01-10-2021, 03:20 PM

RE: 38-116 Restoration - by rfeenstra - 01-10-2021, 07:38 PM

RE: 38-116 Restoration - by Tim Tress - 01-22-2021, 08:43 PM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

Who's Online

There are currently 4849 online users. [Complete List]
» 2 Member(s) | 4847 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me