Got a 39-6 today

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Got a 39-6 today

Radioroslyn
Phorum Expert

Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa

#23

01-03-2020, 12:33 PM

Not a bad idea on those sets to install a thin piece of plastic (like from a blister pak) over the dial so the pointer can't scrape graphics off. You can use the mounting screws for the dial to hold it in place.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry

Find

« Next Oldest | Next Newest »

Messages In This Thread

Got a 39-6 today - by morzh - 09-13-2014, 03:20 PM

RE: Got a 39-6 today - by morzh - 09-13-2014, 03:25 PM

RE: Got a 39-6 today - by sam - 09-13-2014, 07:59 PM

RE: Got a 39-6 today - by Ron Ramirez - 09-13-2014, 08:38 PM

RE: Got a 39-6 today - by morzh - 09-13-2014, 08:43 PM

RE: Got a 39-6 today - by Ron Ramirez - 09-13-2014, 08:53 PM

RE: Got a 39-6 today - by morzh - 09-13-2014, 09:07 PM

RE: Got a 39-6 today - by BenWA - 09-14-2014, 12:21 AM

RE: Got a 39-6 today - by morzh - 09-14-2014, 10:07 AM

RE: Got a 39-6 today - by klondike98 - 09-14-2014, 12:10 PM

RE: Got a 39-6 today - by morzh - 09-14-2014, 05:18 PM

RE: Got a 39-6 today - by PhilcoJohn - 09-14-2014, 06:55 PM

RE: Got a 39-6 today - by morzh - 09-14-2014, 07:17 PM

RE: Got a 39-6 today - by Arran - 09-16-2014, 01:30 AM

RE: Got a 39-6 today - by Jake Blake - 01-01-2020, 10:27 PM

RE: Got a 39-6 today - by Tubeglow20 - 01-02-2020, 12:10 AM

RE: Got a 39-6 today - by rfeenstra - 01-02-2020, 12:46 AM

RE: Got a 39-6 today - by morzh - 01-02-2020, 11:01 AM

RE: Got a 39-6 today - by Radioroslyn - 01-02-2020, 11:42 AM

RE: Got a 39-6 today - by Jake Blake - 01-02-2020, 11:21 PM

RE: Got a 39-6 today - by Tubeglow20 - 01-03-2020, 01:45 AM

RE: Got a 39-6 today - by Jake Blake - 01-03-2020, 09:26 AM

RE: Got a 39-6 today - by Radioroslyn - 01-03-2020, 12:33 PM

RE: Got a 39-6 today - by Jake Blake - 01-03-2020, 01:30 PM

RE: Got a 39-6 today - by Phlogiston - 01-03-2020, 02:04 PM

RE: Got a 39-6 today - by Radioroslyn - 01-03-2020, 02:05 PM

RE: Got a 39-6 today - by Jake Blake - 01-03-2020, 02:53 PM

RE: Got a 39-6 today - by Jake Blake - 01-03-2020, 03:01 PM

RE: Got a 39-6 today - by klondike98 - 01-03-2020, 05:12 PM

RE: Got a 39-6 today - by Phlogiston - 01-03-2020, 07:31 PM

RE: Got a 39-6 today - by Jake Blake - 01-03-2020, 08:15 PM

RE: Got a 39-6 today - by Tubeglow20 - 01-03-2020, 10:17 PM

RE: Got a 39-6 today - by Jake Blake - 01-04-2020, 12:14 AM

RE: Got a 39-6 today - by Art Hoch - 01-07-2020, 11:26 AM

RE: Got a 39-6 today - by Jake Blake - 01-07-2020, 11:52 AM

RE: Got a 39-6 today - by Ron Ramirez - 01-07-2020, 09:33 PM

RE: Got a 39-6 today - by Jake Blake - 01-08-2020, 07:48 AM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM

Who's Online

There are currently 5423 online users. [Complete List]
» 3 Member(s) | 5420 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me