Got a 39-6 today

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Got a 39-6 today

Radioroslyn
Phorum Expert

Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa

#26

01-03-2020, 02:05 PM

Roughly you can figure abt for each watt = abt 100ma. So a 50w set = a .5a fuse.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry

Find

« Next Oldest | Next Newest »

Messages In This Thread

Got a 39-6 today - by morzh - 09-13-2014, 03:20 PM

RE: Got a 39-6 today - by morzh - 09-13-2014, 03:25 PM

RE: Got a 39-6 today - by sam - 09-13-2014, 07:59 PM

RE: Got a 39-6 today - by Ron Ramirez - 09-13-2014, 08:38 PM

RE: Got a 39-6 today - by morzh - 09-13-2014, 08:43 PM

RE: Got a 39-6 today - by Ron Ramirez - 09-13-2014, 08:53 PM

RE: Got a 39-6 today - by morzh - 09-13-2014, 09:07 PM

RE: Got a 39-6 today - by BenWA - 09-14-2014, 12:21 AM

RE: Got a 39-6 today - by morzh - 09-14-2014, 10:07 AM

RE: Got a 39-6 today - by klondike98 - 09-14-2014, 12:10 PM

RE: Got a 39-6 today - by morzh - 09-14-2014, 05:18 PM

RE: Got a 39-6 today - by PhilcoJohn - 09-14-2014, 06:55 PM

RE: Got a 39-6 today - by morzh - 09-14-2014, 07:17 PM

RE: Got a 39-6 today - by Arran - 09-16-2014, 01:30 AM

RE: Got a 39-6 today - by Jake Blake - 01-01-2020, 10:27 PM

RE: Got a 39-6 today - by Tubeglow20 - 01-02-2020, 12:10 AM

RE: Got a 39-6 today - by rfeenstra - 01-02-2020, 12:46 AM

RE: Got a 39-6 today - by morzh - 01-02-2020, 11:01 AM

RE: Got a 39-6 today - by Radioroslyn - 01-02-2020, 11:42 AM

RE: Got a 39-6 today - by Jake Blake - 01-02-2020, 11:21 PM

RE: Got a 39-6 today - by Tubeglow20 - 01-03-2020, 01:45 AM

RE: Got a 39-6 today - by Jake Blake - 01-03-2020, 09:26 AM

RE: Got a 39-6 today - by Radioroslyn - 01-03-2020, 12:33 PM

RE: Got a 39-6 today - by Jake Blake - 01-03-2020, 01:30 PM

RE: Got a 39-6 today - by Phlogiston - 01-03-2020, 02:04 PM

RE: Got a 39-6 today - by Radioroslyn - 01-03-2020, 02:05 PM

RE: Got a 39-6 today - by Jake Blake - 01-03-2020, 02:53 PM

RE: Got a 39-6 today - by Jake Blake - 01-03-2020, 03:01 PM

RE: Got a 39-6 today - by klondike98 - 01-03-2020, 05:12 PM

RE: Got a 39-6 today - by Phlogiston - 01-03-2020, 07:31 PM

RE: Got a 39-6 today - by Jake Blake - 01-03-2020, 08:15 PM

RE: Got a 39-6 today - by Tubeglow20 - 01-03-2020, 10:17 PM

RE: Got a 39-6 today - by Jake Blake - 01-04-2020, 12:14 AM

RE: Got a 39-6 today - by Art Hoch - 01-07-2020, 11:26 AM

RE: Got a 39-6 today - by Jake Blake - 01-07-2020, 11:52 AM

RE: Got a 39-6 today - by Ron Ramirez - 01-07-2020, 09:33 PM

RE: Got a 39-6 today - by Jake Blake - 01-08-2020, 07:48 AM

View a Printable Version

Users browsing this thread: 3 Guest(s)

Recent Posts
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me