Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

38-116 Restoration
#7

The rectifier socket is wired for a 5X4. It would be easy to wire it to also take a 5U4, which is identical except for the pin out on one side of the filament and the plates. Has anyone done this? I have several 5U4's kicking around, but no extra 5X4's.


Messages In This Thread
38-116 Restoration - by rfeenstra - 12-30-2019, 09:10 PM
RE: 38-116 Restoration - by rfeenstra - 12-30-2019, 11:46 PM
RE: 38-116 Restoration - by rfeenstra - 01-02-2020, 01:39 AM
RE: 38-116 Restoration - by rfeenstra - 01-04-2020, 04:33 PM
RE: 38-116 Restoration - by KCMike - 01-04-2020, 05:46 PM
RE: 38-116 Restoration - by rfeenstra - 01-04-2020, 07:03 PM
RE: 38-116 Restoration - by rfeenstra - 01-04-2020, 08:08 PM
RE: 38-116 Restoration - by rfeenstra - 01-04-2020, 08:49 PM
RE: 38-116 Restoration - by rfeenstra - 01-07-2020, 12:13 AM
RE: 38-116 Restoration - by rfeenstra - 01-08-2020, 08:35 PM
RE: 38-116 Restoration - by rfeenstra - 01-09-2020, 11:47 PM
RE: 38-116 Restoration - by KCMike - 01-10-2020, 09:55 AM
RE: 38-116 Restoration - by rfeenstra - 01-13-2020, 03:12 AM
RE: 38-116 Restoration - by morzh - 01-13-2020, 08:47 AM
RE: 38-116 Restoration - by Nathan Slingerland - 01-13-2020, 11:55 AM
RE: 38-116 Restoration - by rfeenstra - 01-17-2020, 12:10 AM
RE: 38-116 Restoration - by rfeenstra - 01-17-2020, 12:14 AM
RE: 38-116 Restoration - by Jake Blake - 01-17-2020, 09:38 AM
RE: 38-116 Restoration - by rfeenstra - 01-21-2020, 03:35 PM
RE: 38-116 Restoration - by mikethedruid - 01-21-2020, 05:49 PM
RE: 38-116 Restoration - by rfeenstra - 01-21-2020, 06:22 PM
RE: 38-116 Restoration - by Nicko - 02-02-2020, 09:51 PM
RE: 38-116 Restoration - by klondike98 - 02-02-2020, 10:21 PM
RE: 38-116 Restoration - by rfeenstra - 02-16-2020, 03:25 PM
RE: 38-116 Restoration - by quick573 - 01-10-2021, 03:20 PM
RE: 38-116 Restoration - by rfeenstra - 01-10-2021, 07:38 PM
RE: 38-116 Restoration - by Tim Tress - 01-22-2021, 08:43 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio.  This is a shame because this should be a good performer.  2A5...MrFixr55 — 06:48 AM
American Bosch Model 802 auto radio
I think it would come under either American Bosch or United American Bosch. American Bosch made sets for the American We...Arran — 05:53 AM
trying to identify this wire type
Thanks to all for the feedback. As Arran said, it is probably an older replacement and yes it has a grid cap so I will ...georgetownjohn — 09:32 PM
trying to identify this wire type
It's possible that the red wire, actually a grid cap lead, is a very old replacement, I can't remember seeing a pre 1939...Arran — 09:18 PM
Gilfillan Brothers Car Radio?
Hi everyone,  Special thanks to Joe Rossi for tracking down this obscure radio and thanks to others who took up the hun...Antipodal — 08:15 PM
trying to identify this wire type
Here's one source for your wire of many. Take care and BE HEALTHY! Gary P.S. Can't get the right color you need? I ...GarySP — 06:40 PM
trying to identify this wire type
...and modern wire of the appropriate gauges and insulation V-rating (300V minimum, usually shown right on the wire) is ...morzh — 05:47 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
I have a question about this radio, is there anyone that has access to this radio that has an intact unmolested speaker ...captainclock1988 — 04:28 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Well what makes me confuse all of those companies is that all three of those companies (Setchell-Carlson, Stromberg-Carl...captainclock1988 — 04:21 PM
trying to identify this wire type
The red wire is rubber covered wire. The others are cotton braid over rubber often in colors or a tracer, also strand...Chas — 02:43 PM

[-]
Who's Online
There are currently no members online.

>