1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Tuning Tool Availability
rfeenstra
Phorum Expert
*****
Posts: 1,185
Threads: 49
Joined: Oct 2017
City: Allendale, MI
#10

01-27-2020, 10:39 PM
I love to use Steve's tool but there have been a couple of instances where it just would not fit.  I had to resort to my old, ground down metal nut driver with tape to insulate it.  If it affected the tuning, which it has in a couple of instances, I adjust, remove, check, adjust again. remove and check until I get it right.  it takes a bit of extra effort but it works.
Find
« Next Oldest | Next Newest »


Messages In This Thread
Tuning Tool Availability - by Jimmiek - 01-25-2020, 02:58 PM
RE: Tuning Tool Availability - by Stall-U-Rated - 01-25-2020, 03:19 PM
RE: Tuning Tool Availability - by klondike98 - 01-25-2020, 06:18 PM
RE: Tuning Tool Availability - by Jimmiek - 01-25-2020, 08:47 PM
RE: Tuning Tool Availability - by klondike98 - 01-26-2020, 12:35 PM
RE: Tuning Tool Availability - by morzh - 01-27-2020, 09:44 PM
RE: Tuning Tool Availability - by rfeenstra - 01-27-2020, 10:39 PM
RE: Tuning Tool Availability - by morzh - 01-28-2020, 11:00 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Looking for place to donate unique Philco Philco J-1930 Prototype
Given the 1960s vintage, it is likely that the cartridge is ceramic, likely more stable. The changer looks like a Voice...MrFixr55 — 05:03 PM
Jackson 665 j2 schematic request
FIXED!daveone23 — 03:55 PM
Bakelite crack repair - what is best epoxy?
Thanks everyone. I appreciate you sharing your experience and looks like I'll work with the 24 hr two part clear epoxy....de371 — 10:25 PM
Jackson 665 j2 schematic request
Without a schematic its going to be hard tracing the wire wound spool resistors.daveone23 — 05:21 PM
Jackson 665 j2 schematic request
Looking for a schematic for the 665 j2 multimeter.daveone23 — 04:42 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
>>I'll write to the Henry Ford. I heard, his secretary answers his mail, not he himself.morzh — 12:15 PM
Philco 48-200 alignment questions
Just checked the power cord and I did in fact wire it so the hot side (small prong) goes to the switch.transitony — 11:52 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
Thanks for the suggestions.  I'll write to the Henry Ford.   That would certainly make sense since by the time this prod...jeibner — 11:49 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
For what it's worth, the Henry Ford Museum and Greenfield Village in Dearborn, Michigan may be an option. The obvious ...GarySP — 11:39 AM
Help with Readrite 410 tube tester
Mike and I just had a short discussion yesterday about this very subject. So often it's the connections. Ya gotta have t...RodB — 10:08 AM

[-]
Who's Online
There are currently 3219 online users. [Complete List]
» 2 Member(s) | 3217 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration