1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
39-6 without the veneer inlay ;-(
Jake Blake
Banned
Posts: 816
Threads: 25
Joined: Mar 2014
City: Louisville, KY
#21

01-28-2020, 10:01 PM
I'm on the grill cloth now.
Ordered a piece from Radio Daze and bought some spray adhesive I thought would be good to use to stick the cloth to the cardboard piece the old cloth was glued to.  But when I did, the spray glue showed darkened areas through the front side.  Maybe I didn't let the glue set up enough, but I'm wondering if there is a special product I should have used.  Or maybe I shouldn't even try to glue that material....maybe it should be stapled to a piece of luan, like the cardboard piece is stapled to the inside of the radio .   Icon_question
Find
« Next Oldest | Next Newest »


Messages In This Thread
39-6 without the veneer inlay ;-( - by Jake Blake - 03-31-2019, 11:28 PM
RE: 39-6 without the veneer inlay ;-( - by morzh - 04-01-2019, 08:31 AM
RE: 39-6 without the veneer inlay ;-( - by morzh - 04-02-2019, 09:50 AM
RE: 39-6 without the veneer inlay ;-( - by KCMike - 01-14-2020, 08:14 PM
RE: 39-6 without the veneer inlay ;-( - by Jake Blake - 01-28-2020, 10:01 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
I seem to remember eliminating a squeal by changing the IF frequency by a few KHz. Not that you should put too much tru...fenbach — 08:48 PM
Philco 42-390, code 121 speaker
These speakers pop up on eBay regularly, even if at bloated prices. Honestly, have not seen many parts on swapmeets.morzh — 08:38 PM
Philco 38-7 Speaker
The put-put is not like the speaker problem.morzh — 08:29 PM
Mission Bell Model 19A Car Radio
Hello everyone,  As mentioned in my last post I was going to see if the vibrator / rectifier section could be persuaded...Antipodal — 08:21 PM
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM

[-]
Who's Online
There are currently 5025 online users. [Complete List]
» 1 Member(s) | 5024 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration