1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Parts list or Volume Pot Value
Radioroslyn
Phorum Expert
*****
Posts: 7,270
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#18

01-30-2011, 03:16 PM
Great new Jerry! Glad you got it going again. Some of those "simple" things can drive you nutz! You beat me to the punch, I was going to drop you a PM to see how you where making out.
Terry
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
« Next Oldest | Next Newest »


Messages In This Thread
Parts list or Volume Pot Value - by JGatewood - 12-27-2010, 10:11 AM
Re: Parts list or Volume Pot Value - by 7estatdef - 12-27-2010, 11:15 AM
Re: Parts list or Volume Pot Value - by 7estatdef - 12-28-2010, 06:29 PM
Re: Parts list or Volume Pot Value - by JGatewood - 01-08-2011, 10:03 AM
Re: Parts list or Volume Pot Value - by 7estatdef - 01-09-2011, 06:02 AM
Re: Parts list or Volume Pot Value - by JGatewood - 01-09-2011, 09:50 PM
Re: Parts list or Volume Pot Value - by 7estatdef - 01-10-2011, 03:48 AM
Re: Parts list or Volume Pot Value - by JGatewood - 01-10-2011, 06:04 AM
Re: Parts list or Volume Pot Value - by JGatewood - 01-10-2011, 06:12 AM
Re: Parts list or Volume Pot Value - by JGatewood - 01-13-2011, 06:02 AM
Re: Parts list or Volume Pot Value - by 7estatdef - 01-13-2011, 05:06 PM
Re: Parts list or Volume Pot Value - by JGatewood - 01-14-2011, 06:21 AM
Re: Parts list or Volume Pot Value - by 7estatdef - 01-14-2011, 05:44 PM
Re: Parts list or Volume Pot Value - by JGatewood - 01-30-2011, 02:10 PM
Re: Parts list or Volume Pot Value - by 7estatdef - 01-30-2011, 03:16 PM
Re: Parts list or Volume Pot Value - by JGatewood - 01-30-2011, 04:20 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Bakelite crack repair - what is best epoxy?
Thanks everyone. I appreciate you sharing your experience and looks like I'll work with the 24 hr two part clear epoxy....de371 — 10:25 PM
Jackson 665 j2 schematic request
Without a schematic its going to be hard tracing the wire wound spool resistors.daveone23 — 05:21 PM
Jackson 665 j2 schematic request
Looking for a schematic for the 665 j2 multimeter.daveone23 — 04:42 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
>>I'll write to the Henry Ford. I heard, his secretary answers his mail, not he himself.morzh — 12:15 PM
Philco 48-200 alignment questions
Just checked the power cord and I did in fact wire it so the hot side (small prong) goes to the switch.transitony — 11:52 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
Thanks for the suggestions.  I'll write to the Henry Ford.   That would certainly make sense since by the time this prod...jeibner — 11:49 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
For what it's worth, the Henry Ford Museum and Greenfield Village in Dearborn, Michigan may be an option. The obvious ...GarySP — 11:39 AM
Help with Readrite 410 tube tester
Mike and I just had a short discussion yesterday about this very subject. So often it's the connections. Ya gotta have t...RodB — 10:08 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
We have a regional museum here in the Twin Cities called The Pavek Museum. They have an extensive collection of communic...RodB — 09:30 AM
Philco 89B code 123 newbie
I did some nosing around and found that the original caps were 4 3/4" long x 1 5/16" in dia. Guess what 1"...Radioroslyn — 09:28 AM

[-]
Who's Online
There are currently 4702 online users. [Complete List]
» 2 Member(s) | 4700 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration