Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Signal Generator Help
#1

Hello everone I just put in an offer on fleabay for a Radio City Products Model 705A Signal Generator and it appears to have at least its RF Probe still the AF Probes don't appear to be present but look to be a standard banana plug style probes which would be fairly easy to acquire or make new ones. 

If they accept my offer I would be getting it for $25 plus $25 shipping, which is the cheapest I've seen them go for, as they seem to go for as much as a couple thousand for a high end Hewlett-Packard unit without its probes which I think seems a bit over priced for a piece of equipment that not many people use anymore, except radio repair hobbyists like us.

My question is, how does one work one of these, and can one find the manuals for these things online? I was thinking that the Boat Anchor Manual Archive would be one place that should have manuals for signal generators like this but I'm not sure.

Any help would be appreciated in this subject.


Messages In This Thread
Signal Generator Help - by captainclock1988 - 04-16-2020, 07:53 PM
RE: Signal Generator Help - by captainclock1988 - 04-16-2020, 07:56 PM
RE: Signal Generator Help - by morzh - 04-16-2020, 08:20 PM
RE: Signal Generator Help - by captainclock1988 - 04-16-2020, 08:44 PM
RE: Signal Generator Help - by morzh - 04-16-2020, 09:27 PM
RE: Signal Generator Help - by captainclock1988 - 04-16-2020, 09:50 PM
RE: Signal Generator Help - by morzh - 04-16-2020, 10:14 PM
RE: Signal Generator Help - by captainclock1988 - 04-16-2020, 10:43 PM
RE: Signal Generator Help - by morzh - 04-16-2020, 10:50 PM
RE: Signal Generator Help - by captainclock1988 - 04-16-2020, 11:08 PM
RE: Signal Generator Help - by morzh - 04-16-2020, 11:24 PM
RE: Signal Generator Help - by captainclock1988 - 04-16-2020, 11:34 PM
RE: Signal Generator Help - by morzh - 04-16-2020, 11:51 PM
RE: Signal Generator Help - by 462ron - 04-17-2020, 08:01 AM
RE: Signal Generator Help - by Eliot Ness - 04-17-2020, 11:00 AM
RE: Signal Generator Help - by captainclock1988 - 04-17-2020, 07:44 PM
RE: Signal Generator Help - by captainclock1988 - 04-21-2020, 02:28 PM
RE: Signal Generator Help - by rfeenstra - 04-21-2020, 03:14 PM
RE: Signal Generator Help - by captainclock1988 - 04-21-2020, 07:45 PM
RE: Signal Generator Help - by 462ron - 04-22-2020, 07:53 AM
RE: Signal Generator Help - by captainclock1988 - 04-22-2020, 09:16 AM
RE: Signal Generator Help - by John Bartley - 04-22-2020, 11:10 AM
RE: Signal Generator Help - by captainclock1988 - 04-22-2020, 11:17 AM
RE: Signal Generator Help - by 462ron - 04-23-2020, 08:37 AM
RE: Signal Generator Help - by 462ron - 04-23-2020, 09:04 AM
RE: Signal Generator Help - by captainclock1988 - 04-23-2020, 12:08 PM
RE: Signal Generator Help - by captainclock1988 - 04-26-2020, 09:15 PM
RE: Signal Generator Help - by 462ron - 04-27-2020, 07:50 AM
RE: Signal Generator Help - by captainclock1988 - 04-27-2020, 04:18 PM
RE: Signal Generator Help - by captainclock1988 - 04-27-2020, 10:21 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Gilfillan Brothers Car Radio?
There is a Mission Bell model 19/19A that could be what you’re looking for, Riders vol 4. It has the tube line-up of: 0Z...Joe Rossi — 05:01 PM
Looking for verification of correct schematic.
Definitely 870044RossH — 01:12 PM
12' Philco
Wonder if the chassis was big too.daveone23 — 12:38 PM
Philco 38-2 Automatic Tuning
Hi Ron, I have sent Radio Daze my concerns with the dial so I guess we will see. They used my original to make the repro...dconant — 12:27 PM
Hickok AC51 tube tester
How does the  5W4 and 83 tube filaments get fed?martinj — 12:25 PM
462ron
Hi Dan, your original dial appears to be lighter, easier to allow light through. My original is similar except it’s crac...462ron — 12:07 PM
Philco 38-2 Automatic Tuning
I received my new 38-2 dial. I'm a little disappointed. As you can see in the picture the blues have a white shadow. The...dconant — 11:13 AM
Philco 38-2 Low Volume
I have been playing my 38-2 for a while now and it is doing very well. I did have to replace the 6A8 (osc) as it develop...dconant — 11:03 AM
Philco Speaker Spider
Hello, Does anyone with a 3 D printer make the spiders for those old Philco speakers? That might be a good idea for some...dconant — 09:41 AM
Philco 16B Parts
Hello, I'm looking to buy a 16B but I'm not so sure of what I am looking at. First as seen from the picture it looks lik...dconant — 09:17 AM

[-]
Who's Online
There are currently 2792 online users. [Complete List]
» 1 Member(s) | 2791 Guest(s)
Avatar

>