Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 70 output transformer
#5

According to the speaker chart in the library, it should be a K3 with a voice coil impedance of .7 ohms and a primary out put transformer DC resistance of 450 ohms. It doesn't give the secondary DC ohms value, but it would be low. I would measure mine but it has a replacement transformer in it.


Messages In This Thread
Philco 70 output transformer - by radio1 - 05-06-2020, 06:49 PM
RE: Philco 70 output transformer - by Radioroslyn - 05-06-2020, 07:32 PM
RE: Philco 70 output transformer - by radio1 - 05-06-2020, 07:40 PM
RE: Philco 70 output transformer - by klondike98 - 05-06-2020, 09:45 PM
RE: Philco 70 output transformer - by rfeenstra - 05-06-2020, 10:31 PM
RE: Philco 70 output transformer - by klondike98 - 05-06-2020, 10:56 PM
RE: Philco 70 output transformer - by radio1 - 05-07-2020, 04:45 AM
RE: Philco 70 output transformer - by Steve Davis - 05-07-2020, 07:58 AM
RE: Philco 70 output transformer - by radio1 - 05-07-2020, 08:59 AM
RE: Philco 70 output transformer - by radio1 - 05-07-2020, 10:20 AM
RE: Philco 70 output transformer - by morzh - 05-07-2020, 10:40 AM
RE: Philco 70 output transformer - by rfeenstra - 05-07-2020, 11:01 AM
RE: Philco 70 output transformer - by radio1 - 05-07-2020, 11:21 AM
RE: Philco 70 output transformer - by morzh - 05-07-2020, 11:46 AM
RE: Philco 70 output transformer - by rfeenstra - 05-07-2020, 11:56 AM
RE: Philco 70 output transformer - by radio1 - 05-07-2020, 06:34 PM
RE: Philco 70 output transformer - by morzh - 05-07-2020, 07:46 PM
RE: Philco 70 output transformer - by radio1 - 05-08-2020, 03:17 PM
RE: Philco 70 output transformer - by morzh - 05-08-2020, 03:51 PM
RE: Philco 70 output transformer - by radio1 - 05-18-2020, 05:52 PM
RE: Philco 70 output transformer - by radio1 - 05-19-2020, 07:26 PM
RE: Philco 70 output transformer - by radio1 - 05-27-2020, 07:19 PM
RE: Philco 70 output transformer - by radio1 - 06-06-2020, 07:22 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

[-]
Who's Online
There are currently no members online.

>