Q1791WA - first project!

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Q1791WA - first project!

Qbinalex
Junior Member

Posts: 8
Threads: 1
Joined: Jul 2019
City: Philadelphia State, Province, Country: PA

#18

05-08-2020, 09:48 PM

Radioroslyn - you were right! Swapped out 3 power supply capacitors and it's working beautifully now!

Now that I can enjoy some tunes, I'm looking into fix other pieces of the cabinet. Are there any suggestion where I can source similar hinges for the back? The one on the left back side is broken (image attached).

Thank you again for all of the help!

Attached Files Image(s)

(This post was last modified: 05-08-2020, 09:52 PM by Qbinalex.)

Find

« Next Oldest | Next Newest »

Messages In This Thread

Q1791WA - first project! - by Qbinalex - 08-13-2019, 12:14 AM

RE: Q1791WA - first project! - by morzh - 08-13-2019, 08:37 AM

RE: Q1791WA - first project! - by Qbinalex - 08-13-2019, 09:49 AM

RE: Q1791WA - first project! - by Scott D - 08-18-2019, 10:35 PM

RE: Q1791WA - first project! - by Stall-U-Rated - 08-19-2019, 12:30 AM

RE: Q1791WA - first project! - by Arohn19 - 08-19-2019, 08:39 PM

RE: Q1791WA - first project! - by Arohn19 - 08-19-2019, 08:46 PM

RE: Q1791WA - first project! - by Qbinalex - 08-19-2019, 10:56 PM

RE: Q1791WA - first project! - by mikethedruid - 08-19-2019, 11:08 PM

RE: Q1791WA - first project! - by Jake Blake - 08-20-2019, 07:41 AM

RE: Q1791WA - first project! - by Ron Ramirez - 08-20-2019, 02:05 PM

RE: Q1791WA - first project! - by Qbinalex - 08-20-2019, 03:45 PM

RE: Q1791WA - first project! - by Qbinalex - 04-20-2020, 08:43 PM

RE: Q1791WA - first project! - by Radioroslyn - 04-20-2020, 09:24 PM

RE: Q1791WA - first project! - by Qbinalex - 04-20-2020, 09:44 PM

RE: Q1791WA - first project! - by Radioroslyn - 04-20-2020, 10:15 PM

RE: Q1791WA - first project! - by Qbinalex - 04-20-2020, 10:28 PM

RE: Q1791WA - first project! - by Qbinalex - 05-08-2020, 09:48 PM

View a Printable Version

Users browsing this thread: 3 Guest(s)

Recent Posts
trying to identify this wire type
The red wire is rubber covered wire. The others are cotton braid over rubber often in colors or a tracer, also strand...Chas — 02:43 PM
trying to identify this wire type
Greetings Phorum members, Hope you can help me identify this type of wire in the photo I have attached. I am not sure ...georgetownjohn — 01:53 PM
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind. Check any soldered, riveted ground conne...Chas — 01:24 PM
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM

Who's Online

There are currently 4499 online users. [Complete List]
» 1 Member(s) | 4498 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me