Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

40-201 oscillator not working.
#4

Hi Tom,
Next I would check the resistance of #28 both pri and sec. Both should very low. Connect your ohm meter to the stator of the tuning cap the osc section and measure the resistance. Switch must but set for manual tuning. The PB are a separate tuned circuit so if the bcb osc coil was bad the PB should still work. You may need to adjust the ant and osc trimmers if the set came from out of your area. Maybe a switch issue.
On #28 the winding that has the hv on it is the feedback. All the other windings are the tuned circuits for each band.

>Now how to get it going?
Now isn't that the $64 question! Just keep chipping away at it till you find the ultimate cause. It can be really repetitive....
>I might find specifications for those coils?
I don't think they are listed anywhere.
>Correct me if I'm making bad assumptions here.
I hope so cauz the osc coil is a pita. Have to do some more troubleshooting.
GL

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry


Messages In This Thread
40-201 oscillator not working. - by Tomie - 04-30-2020, 03:15 PM
RE: 40-201 oscillator not working. - by Tomie - 05-11-2020, 10:19 AM
RE: 40-201 oscillator not working. - by Radioroslyn - 05-11-2020, 08:00 PM
RE: 40-201 oscillator not working. - by Tomie - 05-12-2020, 12:32 PM
RE: 40-201 oscillator not working. - by Tomie - 05-12-2020, 12:38 PM
RE: 40-201 oscillator not working. - by Tomie - 05-16-2020, 10:35 AM
RE: 40-201 oscillator not working. - by RodB - 05-16-2020, 11:33 AM
RE: 40-201 oscillator not working. - by Tomie - 05-16-2020, 01:26 PM
RE: 40-201 oscillator not working. - by RodB - 05-16-2020, 04:17 PM
RE: 40-201 oscillator not working. - by Tomie - 05-16-2020, 05:08 PM
RE: 40-201 oscillator not working. - by RodB - 05-16-2020, 06:02 PM
RE: 40-201 oscillator not working. - by Tomie - 05-17-2020, 11:57 AM
RE: 40-201 oscillator not working. - by RodB - 05-17-2020, 05:03 PM
RE: 40-201 oscillator not working. - by Tomie - 05-18-2020, 11:13 AM
RE: 40-201 oscillator not working. - by Tomie - 05-18-2020, 12:15 PM
RE: 40-201 oscillator not working. - by Tomie - 05-18-2020, 05:09 PM
RE: 40-201 oscillator not working. - by RodB - 05-18-2020, 07:43 PM
RE: 40-201 oscillator not working. - by Tomie - 05-19-2020, 12:54 PM
RE: 40-201 oscillator not working. - by RodB - 05-19-2020, 03:56 PM
RE: 40-201 oscillator not working. - by Tomie - 05-21-2020, 06:03 PM
RE: 40-201 oscillator not working. - by RodB - 05-21-2020, 09:03 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
Outstanding work indeed. I wish I could come up with solutions like this.slford310 — 11:16 PM
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM

[-]
Who's Online
There are currently 3959 online users. [Complete List]
» 1 Member(s) | 3958 Guest(s)
Avatar

>