1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
High voltage readings
RodB
Phorum Expert
*****
Posts: 990
Threads: 40
Joined: Feb 2015
City: Roseville, MN
#15

05-12-2020, 09:19 AM
I'm not entirely sure how this affects the B+ but the choke coil has some inductive reactance to the pulsating DC, adding to the resistance. Therefore, if the choke coil is 1000 ohms you can use a 1200 to 1500 ohm resistor to replace it. You should be able to use the replacement resistor to tweek the B+ without much adverse effect.
Find
« Next Oldest | Next Newest »


Messages In This Thread
High voltage readings - by Tom45acp - 05-08-2020, 05:37 PM
RE: High voltage readings - by gregb - 05-08-2020, 05:50 PM
RE: High voltage readings - by Tom45acp - 05-08-2020, 07:17 PM
RE: High voltage readings - by Radioroslyn - 05-08-2020, 08:44 PM
RE: High voltage readings - by Tom45acp - 05-09-2020, 04:00 PM
RE: High voltage readings - by Steve Davis - 05-09-2020, 05:57 PM
RE: High voltage readings - by morzh - 05-09-2020, 06:31 PM
RE: High voltage readings - by Tom45acp - 05-10-2020, 08:29 PM
RE: High voltage readings - by morzh - 05-10-2020, 09:01 PM
RE: High voltage readings - by Tom45acp - 05-11-2020, 08:59 AM
RE: High voltage readings - by morzh - 05-11-2020, 10:42 AM
RE: High voltage readings - by Tom45acp - 05-11-2020, 06:44 PM
RE: High voltage readings - by morzh - 05-11-2020, 08:45 PM
RE: High voltage readings - by Tom45acp - 05-12-2020, 08:44 AM
RE: High voltage readings - by RodB - 05-12-2020, 09:19 AM
RE: High voltage readings - by morzh - 05-12-2020, 10:18 AM
RE: High voltage readings - by Tom45acp - 05-12-2020, 12:12 PM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM
Model 28L
Hello, I'm restoring a Philco 28L and the output transformer is open. Part number of the transformer is 32-7020. Can...HORSTE — 10:32 AM

[-]
Who's Online
There are currently 6648 online users. [Complete List]
» 2 Member(s) | 6646 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration