Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

51-1733 alignment questions
#13

https://philcoradio.com/library/download...-final.pdf Seems pretty clear to me. NA is awful!!

Don't really care about what the Sam's sez values or placement. It just confuses things. The resistor a cap you mention are in the cathode circuit of the oscillator. They vary the gain of the oscillator tube. They are not a frequency determining components.

I'm thinking they something wrong w/the IF alignment. You shouldn't have to bottom out the slugs. A few things to check. Frequency with a counter @455kc. With the generator set up at 455kc and connect up. Move the dial on the Philco and if the signal disappears you were not on the IF frequency. Always when doing an alignment keep the generator level to a minimum. This means so you can just barely hear it then peak up the adjustment. turn the generator down till you get all of the 455kc transformers peaked up. I usually go over them a couple of times to be sure. Having the generator level up can cause the avc to lower the gain of the tubes in the avc line.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry


Messages In This Thread
51-1733 alignment questions - by Wilryn - 05-10-2020, 03:25 PM
RE: 51-1733 alignment questions - by Radioroslyn - 05-10-2020, 08:59 PM
RE: 51-1733 alignment questions - by Wilryn - 05-10-2020, 11:23 PM
RE: 51-1733 alignment questions - by Wilryn - 05-11-2020, 12:16 AM
RE: 51-1733 alignment questions - by Wilryn - 05-11-2020, 08:55 AM
RE: 51-1733 alignment questions - by RodB - 05-11-2020, 11:45 AM
RE: 51-1733 alignment questions - by Wilryn - 05-11-2020, 04:29 PM
RE: 51-1733 alignment questions - by Radioroslyn - 05-11-2020, 08:02 PM
RE: 51-1733 alignment questions - by Wilryn - 05-12-2020, 02:39 PM
RE: 51-1733 alignment questions - by Wilryn - 05-13-2020, 12:21 PM
RE: 51-1733 alignment questions - by Radioroslyn - 05-13-2020, 02:40 PM
RE: 51-1733 alignment questions - by Wilryn - 05-13-2020, 05:50 PM
RE: 51-1733 alignment questions - by Radioroslyn - 05-13-2020, 08:12 PM
RE: 51-1733 alignment questions - by Wilryn - 05-14-2020, 06:31 PM
RE: 51-1733 alignment questions - by Radioroslyn - 05-14-2020, 07:25 PM



Users browsing this thread: 4 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM
Model 28L
Hello, I'm restoring a Philco 28L and the output transformer is open. Part number of the transformer is 32-7020. Can...HORSTE — 10:32 AM
Philco 42-1008 conversion kit
I read about a kit to convert the variable speed changer in the Philco 42-1008 into a single speed unit.  That would rem...alangard — 09:30 PM
HiFi (Chifi) tube amp build - but my own design.
Tim Well...a chassis is metal. Magnetic or not, it does not matter. A transformer has some hum to it. It is natural. Th...morzh — 08:40 PM
Hickok AC51 tube tester
I thought the 83 tube was bad because it looked white but it tests strong. Blue gassy though. I checked the fuse, it was...martinj — 08:37 PM

[-]
Who's Online
There are currently no members online.

>