Philco 620

Thread Rating:

Philco 620

Neo6425
Junior Member

Posts: 20
Threads: 3
Joined: May 2020
City: Southold State, Province, Country: NY

#23

05-24-2020, 10:22 AM

Here's an update I removed Replacement part number 66 (Condenser .3Mfd. Bakelite Block - Part# 6287 DU)
[Image: http://www.ispdi.com/Philco/images/Bakelie2.jpg]

and did my best to remove its insides.

[Image: http://www.ispdi.com/Philco/images/bakelite3.jpg]and noticed two terminals are wired together (Top terminals on the left in photo).
[Image: http://www.ispdi.com/Philco/images/bakeliteTop.jpg]
So when restuff this with new .3Mfd caps I am keeping this the same, wired in series. Is that correct?
[Image: http://www.ispdi.com/Philco/images/BakeliteNo1.jpg]

(This post was last modified: 05-24-2020, 10:34 AM by Neo6425.)

Find

« Next Oldest | Next Newest »

Messages In This Thread

Philco 620 - by Neo6425 - 05-11-2020, 02:48 PM

RE: Philco 620 - by morzh - 05-11-2020, 03:11 PM

RE: Philco 620 - by Neo6425 - 05-11-2020, 03:22 PM

RE: Philco 620 - by rfeenstra - 05-11-2020, 03:26 PM

RE: Philco 620 - by Neo6425 - 05-11-2020, 04:30 PM

RE: Philco 620 - by morzh - 05-11-2020, 05:23 PM

RE: Philco 620 - by Neo6425 - 05-11-2020, 09:15 PM

RE: Philco 620 - by morzh - 05-11-2020, 09:23 PM

RE: Philco 620 - by Neo6425 - 05-13-2020, 06:46 PM

RE: Philco 620 - by radiorich - 05-14-2020, 02:39 AM

RE: Philco 620 - by Neo6425 - 05-14-2020, 05:35 PM

RE: Philco 620 - by morzh - 05-14-2020, 05:49 PM

RE: Philco 620 - by radiorich - 05-14-2020, 07:16 PM

RE: Philco 620 - by morzh - 05-14-2020, 07:53 PM

RE: Philco 620 - by GarySP - 05-14-2020, 08:38 PM

RE: Philco 620 - by Neo6425 - 05-14-2020, 08:42 PM

RE: Philco 620 - by GarySP - 05-14-2020, 09:06 PM

RE: Philco 620 - by Radioroslyn - 05-14-2020, 09:39 PM

RE: Philco 620 - by morzh - 05-14-2020, 10:41 PM

RE: Philco 620 - by radiorich - 05-17-2020, 01:28 AM

RE: Philco 620 - by Radioroslyn - 05-17-2020, 10:56 AM

RE: Philco 620 - by Neo6425 - 05-24-2020, 09:24 AM

RE: Philco 620 - by Neo6425 - 05-24-2020, 10:22 AM

RE: Philco 620 - by Neo6425 - 05-24-2020, 10:34 AM

RE: Philco 620 - by morzh - 05-24-2020, 11:39 AM

RE: Philco 620 - by LarryFS - 05-24-2020, 12:21 PM

RE: Philco 620 - by Neo6425 - 05-31-2020, 06:19 PM

Users browsing this thread: 10 Guest(s)

Recent Posts
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM
Model 28L
Hello, I'm restoring a Philco 28L and the output transformer is open. Part number of the transformer is 32-7020. Can...HORSTE — 10:32 AM

Who's Online
There are currently no members online.