1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 38-3 hates me
captainclock1988
Senior Member
****
Posts: 299
Threads: 30
Joined: Dec 2019
City: Elkhart State, Province, Country: Indiana
#14

05-26-2020, 11:17 PM
What make and model of Signal Generator are you using? 

The reason why I ask is because I haver 2 Signal Generators a 1948 Radio City Products Model 705A and a Heathkit Model SG-8 Signal Generator, and the Heathkit SG-8 Signal Generator would produce a tone on Band A but then on Bands B-E it would just produce a buzzing noise that would be able to be "peaked" but wouldn't be a definite tone, but then my Radio City Products unit would create a tone on all of the Signal Generator Bands and on all of the radio bands, so to me it sounds like it may be your signal generator rather than your radio. 

Just my 2 cents. It might be worth checking into.

-Levi
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco 38-3 hates me - by DuMont - 05-18-2020, 05:11 PM
RE: Philco 38-3 hates me - by radiodale - 05-18-2020, 06:32 PM
RE: Philco 38-3 hates me - by DuMont - 05-18-2020, 06:52 PM
RE: Philco 38-3 hates me - by morzh - 05-18-2020, 07:49 PM
RE: Philco 38-3 hates me - by DuMont - 05-18-2020, 07:57 PM
RE: Philco 38-3 hates me - by David - 05-19-2020, 09:05 AM
RE: Philco 38-3 hates me - by DuMont - 05-19-2020, 09:24 AM
RE: Philco 38-3 hates me - by David - 05-19-2020, 03:40 PM
RE: Philco 38-3 hates me - by DuMont - 05-19-2020, 03:52 PM
RE: Philco 38-3 hates me - by DuMont - 05-19-2020, 05:43 PM
RE: Philco 38-3 hates me - by DuMont - 05-19-2020, 06:24 PM
RE: Philco 38-3 hates me - by Tim Tress - 05-24-2020, 08:25 PM
RE: Philco 38-3 hates me - by RodB - 05-25-2020, 08:02 AM
RE: Philco 38-3 hates me - by captainclock1988 - 05-26-2020, 11:17 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM
40-150 General questions
I think RobB has it right. It is a part number and looks like its stamped on the chassis and that wasn't something you ...klondike98 — 11:41 AM
40-150 General questions
It's most likely a part number. Most of Philco part numbers are in that format. I looked at the parts list for this mode...RodB — 08:10 AM
40-150 General questions
Hi Kevin, No, I don't but I like your Quote about being a good electrician. The way I look at it is "The fact ...MrFixr55 — 08:06 AM
Philco 38-7 Speaker
7K should be fine. While not a perfect match (This transformer is meant for 6V6 tubes), Antique Electronic Supply (AES)...MrFixr55 — 08:03 AM

[-]
Who's Online
There are currently 2390 online users. [Complete List]
» 2 Member(s) | 2388 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration