Thorens TD124 restoration

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Thorens TD124 restoration

thirtiesradio
Senior Member

Posts: 344
Threads: 38
Joined: Jun 2011
City: Tustin State, Province, Country: California

#25

09-01-2020, 01:54 PM

Hi Mike.
Hope you got your TD124 working!

I've been using one I restored for a couple years now. I did a full rebuild and installed a new main bearing. Also completely disassembled every part including the motor. I have a Garrard 301 as well.

Here's a photo of my TD124 when first rebuilt. I now use an Ortofon RMG212 arm instead of the SME. I do use an early 12" SME arm on the Garrard.

Best of luck with your Thoren's Mike!

(This post was last modified: 09-01-2020, 02:03 PM by thirtiesradio.)

Find

« Next Oldest | Next Newest »

Messages In This Thread

Thorens TD124 restoration - by morzh - 04-28-2020, 08:15 PM

RE: Thorens TD124 restoration - by morzh - 04-28-2020, 08:25 PM

RE: Thorens TD124 restoration - by KCMike - 04-28-2020, 08:31 PM

RE: Thorens TD124 restoration - by morzh - 04-28-2020, 09:13 PM

RE: Thorens TD124 restoration - by Ron Ramirez - 04-28-2020, 09:30 PM

RE: Thorens TD124 restoration - by morzh - 04-28-2020, 09:45 PM

RE: Thorens TD124 restoration - by KCMike - 04-28-2020, 09:54 PM

RE: Thorens TD124 restoration - by Ron Ramirez - 04-28-2020, 10:17 PM

RE: Thorens TD124 restoration - by morzh - 04-28-2020, 10:23 PM

RE: Thorens TD124 restoration - by KCMike - 04-28-2020, 11:09 PM

RE: Thorens TD124 restoration - by morzh - 04-28-2020, 11:35 PM

RE: Thorens TD124 restoration - by Eliot Ness - 04-29-2020, 01:31 PM

RE: Thorens TD124 restoration - by morzh - 04-29-2020, 01:53 PM

RE: Thorens TD124 restoration - by morzh - 05-06-2020, 05:20 PM

RE: Thorens TD124 restoration - by KCMike - 05-06-2020, 06:18 PM

RE: Thorens TD124 restoration - by morzh - 05-06-2020, 06:26 PM

RE: Thorens TD124 restoration - by morzh - 05-07-2020, 07:43 PM

RE: Thorens TD124 restoration - by KCMike - 05-07-2020, 09:11 PM

RE: Thorens TD124 restoration - by morzh - 05-07-2020, 10:30 PM

RE: Thorens TD124 restoration - by morzh - 05-10-2020, 04:14 PM

RE: Thorens TD124 restoration - by morzh - 05-10-2020, 08:21 PM

RE: Thorens TD124 restoration - by morzh - 05-13-2020, 11:01 AM

RE: Thorens TD124 restoration - by morzh - 05-22-2020, 04:01 PM

RE: Thorens TD124 restoration - by morzh - 05-24-2020, 08:16 PM

RE: Thorens TD124 restoration - by thirtiesradio - 09-01-2020, 01:54 PM

RE: Thorens TD124 restoration - by morzh - 09-01-2020, 03:24 PM

RE: Thorens TD124 restoration - by thirtiesradio - 09-25-2020, 02:20 AM

RE: Thorens TD124 restoration - by morzh - 09-25-2020, 08:46 AM

View a Printable Version

Users browsing this thread: 7 Guest(s)

Recent Posts
IF can wire size and Rubber mounts?
Hello PHORUM members, I am still working on restoration of my PHILCO 37-640. I want to start with rewiring the IF ca...georgetownjohn — 06:32 PM
Gilfillan Brothers Car Radio?
There is a Mission Bell model 19/19A that could be what you’re looking for, Riders vol 4. It has the tube line-up of: 0Z...Joe Rossi — 05:01 PM
Looking for verification of correct schematic.
Definitely 870044RossH — 01:12 PM
12' Philco
Wonder if the chassis was big too.daveone23 — 12:38 PM
Philco 38-2 Automatic Tuning
Hi Ron, I have sent Radio Daze my concerns with the dial so I guess we will see. They used my original to make the repro...dconant — 12:27 PM
Hickok AC51 tube tester
How does the 5W4 and 83 tube filaments get fed?martinj — 12:25 PM
462ron
Hi Dan, your original dial appears to be lighter, easier to allow light through. My original is similar except it’s crac...462ron — 12:07 PM
Philco 38-2 Automatic Tuning
I received my new 38-2 dial. I'm a little disappointed. As you can see in the picture the blues have a white shadow. The...dconant — 11:13 AM
Philco 38-2 Low Volume
I have been playing my 38-2 for a while now and it is doing very well. I did have to replace the 6A8 (osc) as it develop...dconant — 11:03 AM
Philco Speaker Spider
Hello, Does anyone with a 3 D printer make the spiders for those old Philco speakers? That might be a good idea for some...dconant — 09:41 AM

Who's Online

There are currently 3125 online users. [Complete List]
» 2 Member(s) | 3123 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me