Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

19LZX restoration
#31

Aligned the set.
The procedure is well-hidden, but I unearthed sometging from the 89 Rider article.
Very simple alignment. Just IF (3 padders) and 1500 kHz. The lower frequency just aligned itself.
Now have to put it back together and clean up the exterior a bit.

   

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.


Messages In This Thread
19LZX restoration - by morzh - 08-15-2020, 02:47 PM
RE: 19LZX restoration - by morzh - 08-15-2020, 05:46 PM
RE: 19LZX restoration - by morzh - 08-16-2020, 05:45 PM
RE: 19LZX restoration - by Nathan Slingerland - 08-16-2020, 08:20 PM
RE: 19LZX restoration - by morzh - 08-16-2020, 08:28 PM
RE: 19LZX restoration - by Nathan Slingerland - 08-16-2020, 08:32 PM
RE: 19LZX restoration - by morzh - 08-16-2020, 11:32 PM
RE: 19LZX restoration - by Nathan Slingerland - 08-17-2020, 12:06 AM
RE: 19LZX restoration - by morzh - 08-17-2020, 08:10 AM
RE: 19LZX restoration - by Nathan Slingerland - 08-17-2020, 08:22 AM
RE: 19LZX restoration - by morzh - 08-17-2020, 11:54 AM
RE: 19LZX restoration - by morzh - 08-18-2020, 09:54 PM
RE: 19LZX restoration - by Ron Ramirez - 08-18-2020, 10:01 PM
RE: 19LZX restoration - by morzh - 08-18-2020, 10:17 PM
RE: 19LZX restoration - by morzh - 08-20-2020, 08:44 PM
RE: 19LZX restoration - by morzh - 08-22-2020, 04:44 PM
RE: 19LZX restoration - by morzh - 08-22-2020, 09:11 PM
RE: 19LZX restoration - by KCMike - 08-22-2020, 11:07 PM
RE: 19LZX restoration - by morzh - 08-23-2020, 05:03 PM
RE: 19LZX restoration - by morzh - 08-25-2020, 08:25 PM
RE: 19LZX restoration - by Eliot Ness - 08-25-2020, 09:02 PM
RE: 19LZX restoration - by morzh - 08-25-2020, 09:34 PM
RE: 19LZX restoration - by Eliot Ness - 08-26-2020, 09:22 AM
RE: 19LZX restoration - by morzh - 08-26-2020, 09:52 AM
RE: 19LZX restoration - by Eliot Ness - 08-26-2020, 10:26 AM
RE: 19LZX restoration - by morzh - 08-26-2020, 10:57 AM
RE: 19LZX restoration - by morzh - 08-27-2020, 09:33 PM
RE: 19LZX restoration - by morzh - 08-28-2020, 07:51 PM
RE: 19LZX restoration - by morzh - 08-29-2020, 07:03 PM
RE: 19LZX restoration - by Paul Philco322 - 08-29-2020, 09:58 PM
RE: 19LZX restoration - by morzh - 09-01-2020, 08:43 PM
RE: 19LZX restoration - by rfeenstra - 09-01-2020, 11:17 PM
RE: 19LZX restoration - by morzh - 09-02-2020, 08:29 AM
RE: 19LZX restoration - by Eliot Ness - 09-02-2020, 11:39 AM
RE: 19LZX restoration - by rfeenstra - 09-02-2020, 05:34 PM
RE: 19LZX restoration - by morzh - 09-02-2020, 08:59 PM
RE: 19LZX restoration - by morzh - 09-03-2020, 08:58 PM
RE: 19LZX restoration - by Eliot Ness - 09-03-2020, 10:15 PM
RE: 19LZX restoration - by NostalgiaRadioTime - 09-03-2020, 10:48 PM
RE: 19LZX restoration - by morzh - 09-03-2020, 10:56 PM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

[-]
Who's Online
There are currently 5143 online users. [Complete List]
» 1 Member(s) | 5142 Guest(s)
Avatar

>