1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Model 71 oscillator
Radioroslyn
Phorum Expert
*****
Posts: 7,295
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#16

09-10-2020, 08:07 AM
Correct. It's the small most outer winding. It's also the one that fails via decay. It is there to create feedback to cause the oscillator to run. A bit like a regenerative receiver w/o the fones
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
(This post was last modified: 09-10-2020, 08:11 AM by Radioroslyn.)
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Model 71 oscillator - by WB5NEN - 09-06-2020, 02:17 PM
RE: Model 71 oscillator - by Steve Davis - 09-06-2020, 10:16 PM
RE: Model 71 oscillator - by Radioroslyn - 09-07-2020, 08:39 AM
RE: Model 71 oscillator - by WB5NEN - 09-07-2020, 05:16 PM
RE: Model 71 oscillator - by WB5NEN - 09-07-2020, 07:32 PM
RE: Model 71 oscillator - by Radioroslyn - 09-07-2020, 07:53 PM
RE: Model 71 oscillator - by WB5NEN - 09-07-2020, 10:15 PM
RE: Model 71 oscillator - by WB5NEN - 09-08-2020, 01:57 PM
RE: Model 71 oscillator - by Radioroslyn - 09-08-2020, 07:58 PM
RE: Model 71 oscillator - by Steve Davis - 09-08-2020, 11:47 PM
RE: Model 71 oscillator - by WB5NEN - 09-09-2020, 04:19 PM
RE: Model 71 oscillator - by Radioroslyn - 09-09-2020, 06:57 PM
RE: Model 71 oscillator - by RodB - 09-09-2020, 07:00 PM
RE: Model 71 oscillator - by Radioroslyn - 09-09-2020, 08:49 PM
RE: Model 71 oscillator - by WB5NEN - 09-09-2020, 10:18 PM
RE: Model 71 oscillator - by Radioroslyn - 09-10-2020, 08:07 AM
RE: Model 71 oscillator - by WB5NEN - 09-10-2020, 08:50 AM
RE: Model 71 oscillator - by RodB - 09-10-2020, 08:57 AM
RE: Model 71 oscillator - by Radioroslyn - 09-10-2020, 10:34 AM
RE: Model 71 oscillator - by rfeenstra - 09-10-2020, 04:46 PM
RE: Model 71 oscillator - by WB5NEN - 09-10-2020, 10:43 PM
RE: Model 71 oscillator - by rfeenstra - 09-11-2020, 09:38 AM
RE: Model 71 oscillator - by WB5NEN - 09-11-2020, 10:07 AM
RE: Model 71 oscillator - by rfeenstra - 09-11-2020, 12:54 PM
RE: Model 71 oscillator - by rfeenstra - 09-11-2020, 01:05 PM
RE: Model 71 oscillator - by WB5NEN - 09-14-2020, 06:58 PM
RE: Model 71 oscillator - by Radioroslyn - 09-15-2020, 09:46 AM
RE: Model 71 oscillator - by WB5NEN - 09-15-2020, 12:00 PM
RE: Model 71 oscillator - by WB5NEN - 09-18-2020, 07:29 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Need to purchase some accessories for restoration of my Old Philco Radio
Here is a list of resources found in our online library that you might find useful. Mike's Gobs of Knobs email addres...klondike98 — 01:46 PM
First Radio restoration
Hi Tubeman, Welcome to the Philco Phorum.  Phamily Phriendly Pfun with Phine Pholks Phull of Philco Phacts. (See a p...MrFixr55 — 12:33 PM
First Radio restoration
You could post in the WANTED ADs section here on the Phorum and see if anyone has an RF generator that they want to sell...klondike98 — 11:55 AM
Zenith H725
Good ideas, thank you Arrange and Rich. I have the adhesive aluminum foil already and can try that immediately. More ...EdHolland — 10:18 AM
Graphics for majestic 1050 dial glass.
Murf; I found this thread on the ARF, the first photo has a pretty good view of the dial glass. Regards ArranArran — 01:12 AM
Zenith H725
hello Ed, how about that speacial tape used for ducting it's like foil or how about thin piece of aluminum roof flash...radiorich — 12:19 AM
Zenith H725
Ed; One material that I have seen, but never tried for this was material for making exhaust gaskets, it's similar to ...Arran — 11:42 PM
Zenith H725
I just remembered, I have some hi temp silicone rubber material which could do the trick. Or a piece of FR4 laminate. Th...EdHolland — 08:39 PM
Zenith H725
The PSU filter cap arrived today (thank you USPS!) so I will work on that later. Meanwhile, I have the dial, speaker...EdHolland — 06:42 PM
Philco 610B oscillator wiring
Thanks Terry. After checking my notes I think I recorded about -10v at the 6A7 G4/control grid. The screen grid (G3 &...Tubester — 05:59 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration