Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco mod. 20
#2

Ok I give up what did it come out of??
Or is there a part # starting with a K or a S inked on it's frame?

The general answer is not so much. It needs to meet a few criteria. Low impedance output transformer to match the push pull triode output tubes (about 4000 ohm total). Needs to have a push pull output transformer. A speaker from a model 70 looks the same but has a single ended transformer. The field coil needs to have a fairly high dc resistance about 3100 ohms. Most of the later sets the field coils are lower around 1500 ohms.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry


Messages In This Thread
Philco mod. 20 - by Gary T. Lane - 09-26-2020, 02:30 PM
RE: Philco mod. 20 - by Radioroslyn - 09-26-2020, 04:52 PM
RE: Philco mod. 20 - by morzh - 09-26-2020, 06:21 PM
RE: Philco mod. 20 - by radiohenry - 09-26-2020, 06:33 PM
RE: Philco mod. 20 - by radiohenry - 09-26-2020, 06:38 PM
RE: Philco mod. 20 - by morzh - 09-26-2020, 08:31 PM
RE: Philco mod. 20 - by Gary T. Lane - 09-27-2020, 10:39 AM
RE: Philco mod. 20 - by Radioroslyn - 09-27-2020, 12:19 PM
RE: Philco mod. 20 - by Gary T. Lane - 09-27-2020, 01:08 PM
RE: Philco mod. 20 - by Radioroslyn - 09-27-2020, 04:30 PM
RE: Philco mod. 20 - by Gary T. Lane - 09-27-2020, 05:35 PM
RE: Philco mod. 20 - by radiohenry - 09-28-2020, 11:57 AM
RE: Philco mod. 20 - by TA Forbes - 10-29-2020, 08:44 PM
RE: Philco mod. 20 - by morzh - 10-29-2020, 08:48 PM
RE: Philco mod. 20 - by MrFixr55 - 11-27-2020, 12:08 AM
RE: Philco mod. 20 - by morzh - 11-27-2020, 12:15 AM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM
Philco Predicta Siesta picture over time getting dimmer
I found that the wire insulation was burnt.  The fly back needs corona dope! Why would someone put that there?Platinumblonde36 — 01:09 AM
Philco Predicta Siesta picture over time getting dimmer
This is what it looked like beforePlatinumblonde36 — 01:01 AM
Philco Predicta Siesta picture over time getting dimmer
Platinumblonde36 — 12:58 AM
Philco Predicta Siesta picture over time getting dimmer
Platinumblonde36 — 12:57 AM
Philco Predicta Siesta picture over time getting dimmer
I'm finding some strange things in my set and for the most part it's also original, so I need to start going over everyt...Platinumblonde36 — 12:55 AM
12' Philco
Not anymore Mike. Andre The Giant Born: May 19, 1946, Coulommiers, France Died: Jan 28, 1993 (46 years), Paris, Fran...RodB — 11:53 PM
IF can wire size and Rubber mounts?
Renovated Radios do carry what you need. As for the voltage, a wire should be at least 300V-rated.morzh — 11:13 PM

[-]
Who's Online
There are currently no members online.

>