1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 77 field coil rewinding
chalupa13
Junior Member
**
Posts: 26
Threads: 7
Joined: Sep 2020
City: Paramus State, Province, Country: NJ
#7

09-26-2020, 10:02 PM
Thank you all for the suggestions. I think I figured out what wire I need. I weighted the old spool and it was just under 2.5 lb. I matched that weight with wire sold today and came up with awg of 33 that gives me almost exactly 3200 Ohm for 2.5lb of wire, approx 15,500'.
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco 77 field coil rewinding - by chalupa13 - 09-25-2020, 11:53 PM
RE: Philco 77 field coil rewinding - by morzh - 09-26-2020, 12:08 AM
RE: Philco 77 field coil rewinding - by chalupa13 - 09-26-2020, 12:51 AM
RE: Philco 77 field coil rewinding - by Forrest - 09-26-2020, 07:08 AM
RE: Philco 77 field coil rewinding - by morzh - 09-26-2020, 12:01 PM
RE: Philco 77 field coil rewinding - by chalupa13 - 09-26-2020, 10:02 PM
RE: Philco 77 field coil rewinding - by chalupa13 - 09-26-2020, 10:20 PM
RE: Philco 77 field coil rewinding - by radiorich - 09-28-2020, 02:07 AM
RE: Philco 77 field coil rewinding - by chalupa13 - 10-03-2020, 10:40 PM
RE: Philco 77 field coil rewinding - by chalupa13 - 10-16-2020, 03:21 PM
RE: Philco 77 field coil rewinding - by radio1 - 10-20-2020, 07:51 PM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration