Atwater Kent 708

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Atwater Kent 708

Phlogiston
Radio-Fixer-Upper

Posts: 2,118
Threads: 112
Joined: Jun 2010
City: Medford OR (OR what?)

#16

10-18-2020, 10:07 AM

I missed your earlier question:

Heat will "reactivate" (melt) hide glue. Modern wood glue will not stick well to old hide glue. If you ate going to use Elmers, I would scrape away as much hide glue as possible with a razor knife.

"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/

Website Find

« Next Oldest | Next Newest »

Messages In This Thread

Atwater Kent 708 - by rfeenstra - 10-05-2020, 12:51 AM

RE: Atwater Kent 708 - by rfeenstra - 10-05-2020, 12:53 AM

RE: Atwater Kent 708 - by rfeenstra - 10-05-2020, 12:54 AM

RE: Atwater Kent 708 - by rfeenstra - 10-05-2020, 01:05 AM

RE: Atwater Kent 708 - by morzh - 10-05-2020, 09:25 AM

RE: Atwater Kent 708 - by Phlogiston - 10-05-2020, 10:51 AM

RE: Atwater Kent 708 - by rfeenstra - 10-05-2020, 12:00 PM

RE: Atwater Kent 708 - by rfeenstra - 10-05-2020, 08:57 PM

RE: Atwater Kent 708 - by Eliot Ness - 10-06-2020, 08:15 AM

RE: Atwater Kent 708 - by morzh - 10-06-2020, 10:31 AM

RE: Atwater Kent 708 - by Phlogiston - 10-06-2020, 10:50 AM

RE: Atwater Kent 708 - by morzh - 10-06-2020, 03:21 PM

RE: Atwater Kent 708 - by rfeenstra - 10-06-2020, 09:09 PM

RE: Atwater Kent 708 - by Eliot Ness - 10-07-2020, 01:57 PM

RE: Atwater Kent 708 - by rfeenstra - 10-17-2020, 11:11 PM

RE: Atwater Kent 708 - by Phlogiston - 10-18-2020, 10:07 AM

RE: Atwater Kent 708 - by rfeenstra - 10-18-2020, 12:32 PM

RE: Atwater Kent 708 - by rfeenstra - 10-25-2020, 03:43 PM

RE: Atwater Kent 708 - by Paul Philco322 - 10-25-2020, 05:58 PM

RE: Atwater Kent 708 - by Eliot Ness - 10-26-2020, 01:34 PM

RE: Atwater Kent 708 - by Paul Philco322 - 10-26-2020, 08:57 PM

RE: Atwater Kent 708 - by rfeenstra - 11-04-2020, 01:20 PM

RE: Atwater Kent 708 - by NostalgiaRadioTime - 11-05-2020, 01:38 AM

RE: Atwater Kent 708 - by Eliot Ness - 11-05-2020, 08:47 AM

RE: Atwater Kent 708 - by rfeenstra - 11-05-2020, 10:32 PM

RE: Atwater Kent 708 - by tbone - 11-06-2020, 07:50 AM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM

Who's Online

There are currently 4757 online users. [Complete List]
» 1 Member(s) | 4756 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me