Atwater Kent 708

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Atwater Kent 708

rfeenstra
Phorum Expert

Posts: 1,190
Threads: 50
Joined: Oct 2017
City: Allendale, MI

#17

10-18-2020, 12:32 PM

Thanks Russ. The delamination was on the bottom board, just at the edge. I used modern hide glue. Probably doesn't stick much better than other wood glues to old hide glue, but it is holding for now.

Find

« Next Oldest | Next Newest »

Messages In This Thread

Atwater Kent 708 - by rfeenstra - 10-05-2020, 12:51 AM

RE: Atwater Kent 708 - by rfeenstra - 10-05-2020, 12:53 AM

RE: Atwater Kent 708 - by rfeenstra - 10-05-2020, 12:54 AM

RE: Atwater Kent 708 - by rfeenstra - 10-05-2020, 01:05 AM

RE: Atwater Kent 708 - by morzh - 10-05-2020, 09:25 AM

RE: Atwater Kent 708 - by Phlogiston - 10-05-2020, 10:51 AM

RE: Atwater Kent 708 - by rfeenstra - 10-05-2020, 12:00 PM

RE: Atwater Kent 708 - by rfeenstra - 10-05-2020, 08:57 PM

RE: Atwater Kent 708 - by Eliot Ness - 10-06-2020, 08:15 AM

RE: Atwater Kent 708 - by morzh - 10-06-2020, 10:31 AM

RE: Atwater Kent 708 - by Phlogiston - 10-06-2020, 10:50 AM

RE: Atwater Kent 708 - by morzh - 10-06-2020, 03:21 PM

RE: Atwater Kent 708 - by rfeenstra - 10-06-2020, 09:09 PM

RE: Atwater Kent 708 - by Eliot Ness - 10-07-2020, 01:57 PM

RE: Atwater Kent 708 - by rfeenstra - 10-17-2020, 11:11 PM

RE: Atwater Kent 708 - by Phlogiston - 10-18-2020, 10:07 AM

RE: Atwater Kent 708 - by rfeenstra - 10-18-2020, 12:32 PM

RE: Atwater Kent 708 - by rfeenstra - 10-25-2020, 03:43 PM

RE: Atwater Kent 708 - by Paul Philco322 - 10-25-2020, 05:58 PM

RE: Atwater Kent 708 - by Eliot Ness - 10-26-2020, 01:34 PM

RE: Atwater Kent 708 - by Paul Philco322 - 10-26-2020, 08:57 PM

RE: Atwater Kent 708 - by rfeenstra - 11-04-2020, 01:20 PM

RE: Atwater Kent 708 - by NostalgiaRadioTime - 11-05-2020, 01:38 AM

RE: Atwater Kent 708 - by Eliot Ness - 11-05-2020, 08:47 AM

RE: Atwater Kent 708 - by rfeenstra - 11-05-2020, 10:32 PM

RE: Atwater Kent 708 - by tbone - 11-06-2020, 07:50 AM

View a Printable Version

Users browsing this thread: 3 Guest(s)

Recent Posts
trying to identify this wire type
Here's one source for your wire of many. Take care and BE HEALTHY! Gary P.S. Can't get the right color you need? I ...GarySP — 06:40 PM
trying to identify this wire type
...and modern wire of the appropriate gauges and insulation V-rating (300V minimum, usually shown right on the wire) is ...morzh — 05:47 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
I have a question about this radio, is there anyone that has access to this radio that has an intact unmolested speaker ...captainclock1988 — 04:28 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Well what makes me confuse all of those companies is that all three of those companies (Setchell-Carlson, Stromberg-Carl...captainclock1988 — 04:21 PM
trying to identify this wire type
The red wire is rubber covered wire. The others are cotton braid over rubber often in colors or a tracer, also strand...Chas — 02:43 PM
trying to identify this wire type
Greetings Phorum members, Hope you can help me identify this type of wire in the photo I have attached. I am not sure ...georgetownjohn — 01:53 PM
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind. Check any soldered, riveted ground conne...Chas — 01:24 PM
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM

Who's Online

There are currently 3439 online users. [Complete List]
» 3 Member(s) | 3436 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me