1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 38-12 Cabinet Strip
flyer92
Junior Member
**
Posts: 10
Threads: 2
Joined: Oct 2020
City: Menifee State, Province, Country: CA
#18

10-27-2020, 04:24 PM
Well, it is much dirtier than it appears in the photo, and won't match a fully restored cabinet very well, unless I can find a way to clean it carefully.  Parts of it are very delicate and will likely fall apart when I remove it anyway. Just want to have a decent backup if/when that occurs.

Finally located the correct knobs, so just hoping someone can recommend a source for the fabric and pointer...especially the pointer, as I'm learning that these are as scarce as hen's teeth!
(This post was last modified: 10-27-2020, 04:44 PM by flyer92.)
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco 38-12 Cabinet Strip - by flyer92 - 10-15-2020, 01:09 PM
RE: Philco 38-12 Cabinet Strip - by Patrick - 10-16-2020, 04:34 AM
RE: Philco 38-12 Cabinet Strip - by RodB - 10-16-2020, 09:03 AM
RE: Philco 38-12 Cabinet Strip - by flyer92 - 10-16-2020, 09:30 AM
RE: Philco 38-12 Cabinet Strip - by Chas - 10-16-2020, 09:35 AM
RE: Philco 38-12 Cabinet Strip - by Patrick - 10-16-2020, 09:53 AM
RE: Philco 38-12 Cabinet Strip - by Chas - 10-16-2020, 10:13 AM
RE: Philco 38-12 Cabinet Strip - by morzh - 10-16-2020, 12:22 PM
RE: Philco 38-12 Cabinet Strip - by flyer92 - 10-16-2020, 01:31 PM
RE: Philco 38-12 Cabinet Strip - by flyer92 - 10-19-2020, 09:55 PM
RE: Philco 38-12 Cabinet Strip - by Patrick - 10-20-2020, 07:20 AM
RE: Philco 38-12 Cabinet Strip - by flyer92 - 10-20-2020, 09:04 AM
RE: Philco 38-12 Cabinet Strip - by Patrick - 10-20-2020, 11:27 AM
RE: Philco 38-12 Cabinet Strip - by flyer92 - 10-20-2020, 11:43 AM
RE: Philco 38-12 Cabinet Strip - by Patrick - 10-20-2020, 11:58 AM
RE: Philco 38-12 Cabinet Strip - by flyer92 - 10-25-2020, 02:45 PM
RE: Philco 38-12 Cabinet Strip - by Ron Ramirez - 10-27-2020, 03:45 PM
RE: Philco 38-12 Cabinet Strip - by flyer92 - 10-27-2020, 04:24 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
Outstanding work indeed. I wish I could come up with solutions like this.slford310 — 11:16 PM
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration