1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
philco 38-116 125 schematic
RodB
Phorum Expert
*****
Posts: 988
Threads: 40
Joined: Feb 2015
City: Roseville, MN
#2

11-15-2020, 09:39 AM
You can probably use the body-end-dot scheme on these. There was a doggone transition period where the BED was used before the bands became standard. So, if the body is orange, the end band black and middle band red you have a 3000 ohm resistor.
Find
« Next Oldest | Next Newest »


Messages In This Thread
philco 38-116 125 schematic - by mg34.42 - 11-15-2020, 04:03 AM
RE: philco 38-116 125 schematic - by RodB - 11-15-2020, 09:39 AM
RE: philco 38-116 125 schematic - by Radioroslyn - 11-15-2020, 10:03 AM
RE: philco 38-116 125 schematic - by mg34.42 - 11-15-2020, 02:03 PM
RE: philco 38-116 125 schematic - by RodB - 11-15-2020, 02:35 PM
RE: philco 38-116 125 schematic - by Tim Tress - 01-22-2021, 09:08 PM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

[-]
Who's Online
There are currently 5063 online users. [Complete List]
» 1 Member(s) | 5062 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration