Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

RP3 help
#9

So you have a 6A7 doing its thing ( it is normally a osc/mixer in a receiver).

What is your plate voltage? Have you looked at it with a scope, how about a signal sniffer. I would suspect that a really good 6A7 might be required to get good range, not my favorite tube - still trying to get the Strat to osc. on band 5, reliably.

"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/


Messages In This Thread
RP3 help - by rjm - 12-09-2020, 12:47 PM
RE: RP3 help - by Phlogiston - 12-09-2020, 02:52 PM
RE: RP3 help - by rjm - 12-09-2020, 03:08 PM
RE: RP3 help - by David - 12-09-2020, 04:51 PM
RE: RP3 help - by rjm - 12-09-2020, 05:57 PM
RE: RP3 help - by Radioroslyn - 12-09-2020, 06:00 PM
RE: RP3 help - by rjm - 12-09-2020, 06:05 PM
RE: RP3 help - by Radioroslyn - 12-09-2020, 06:18 PM
RE: RP3 help - by Phlogiston - 12-09-2020, 06:25 PM
RE: RP3 help - by rjm - 12-09-2020, 06:45 PM
RE: RP3 help - by rjm - 12-09-2020, 06:54 PM
RE: RP3 help - by Phlogiston - 12-09-2020, 07:01 PM
RE: RP3 help - by rjm - 12-09-2020, 07:17 PM
RE: RP3 help - by Phlogiston - 12-09-2020, 07:42 PM
RE: RP3 help - by morzh - 12-09-2020, 08:52 PM
RE: RP3 help - by rjm - 12-10-2020, 01:19 PM
RE: RP3 help - by rjm - 12-10-2020, 01:21 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
New Philco Repair Bench
I am sure this is the archive, and not the Chuck's site.morzh — 09:50 PM
Made mistake & did not label connection
It's not like we are good friends with that wire and can tell it from other ptetty identical looking wires. Why'n't you...morzh — 09:49 PM
Made mistake & did not label connection
I'm not sure why that wire wasn't covered in the video. I'm pretty sure the 6A8 won't work until that pin is grounded. Y...RodB — 09:47 PM
Made mistake & did not label connection
You'll have to forgive me, I am not sure what you mean.  Can you explain what you are really saying.  If anyone does not...georgetownjohn — 08:05 PM
Made mistake & did not label connection
Those are details better left to the ones who know. Maybe you disconnected the wrong end of the wire.RodB — 06:22 PM
Made mistake & did not label connection
Maybe this is starting to make some sense in my hard head.  Is this why the wire in question was not in the great Ron Ra...georgetownjohn — 04:34 PM
Made mistake & did not label connection
I was correct with the 6A8 pin connection's, 7 and 8 are connected to ground as well as the tube shield (the broken line...RodB — 02:41 PM
Made mistake & did not label connection
What does the dotted line representing that surrounds the tube in the schematic?georgetownjohn — 02:17 PM
Made mistake & did not label connection
Hello John, I have been there either label got lost or was not labeled ! Sincerely Richardradiorich — 02:15 PM
Made mistake & did not label connection
Sorry, it is a Philco 37-640.  Does that help?--Johngeorgetownjohn — 02:14 PM

[-]
Who's Online
There are currently no members online.

>