Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Another aqusition a Model 20
#13

The reason you are getting a higher reading is you are using a VTVM or digital meter. In the old days, voltmeters presented a load (about 2,000 ohms per per volt) on whatever was being measured, so that's why the specs were written that way.


Messages In This Thread
Another aqusition a Model 20 - by 7estatdef - 02-26-2011, 07:00 PM
Re: Another aqusition - by TA Forbes - 02-27-2011, 01:00 AM
Re: Another aqusition - by 7estatdef - 02-27-2011, 09:31 AM
Re: Another aqusition - by TA Forbes - 02-27-2011, 02:07 PM
Re: Another aqusition - by 7estatdef - 02-27-2011, 03:26 PM
Re: Another aqusition - by 7estatdef - 02-28-2011, 09:15 PM
Re: Another aqusition - by 7estatdef - 02-28-2011, 10:22 PM
Re: Another aqusition - by 7estatdef - 03-01-2011, 09:22 AM
Re: Another aqusition - by 7estatdef - 03-01-2011, 11:01 PM
Re: Another aqusition a Model 20 - by 7estatdef - 03-02-2011, 11:06 PM
Re: Another aqusition a Model 20 - by Ron Ramirez - 03-03-2011, 08:48 AM
Re: Another aqusition a Model 20 - by 7estatdef - 03-17-2011, 05:51 PM
Re: Another aqusition a Model 20 - by codefox1 - 03-18-2011, 10:36 AM
Re: Another aqusition a Model 20 - by 7estatdef - 03-18-2011, 05:44 PM
Re: Another aqusition a Model 20 - by 7estatdef - 03-18-2011, 07:04 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM

[-]
Who's Online
There are currently 4550 online users. [Complete List]
» 1 Member(s) | 4549 Guest(s)
Avatar

>