AS4 Hobbyists Radio

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

AS4 Hobbyists Radio

Daniel Bingamon
Member

Posts: 53
Threads: 7
Joined: Nov 2020
City: KINGS MILLS State, Province, Country: OH

12-30-2020, 11:24 PM

Good catches. I'm correcting it.

I have a question. Most AA5 drawings have the second anode to the diode on the 12SQ7 to ground. Would tying both anodes together cause noise or something?

Find

« Next Oldest | Next Newest »

Messages In This Thread

AS4 Hobbyists Radio - by Daniel Bingamon - 12-24-2020, 04:18 PM

RE: AS4 Hobbyists Radio - by Daniel Bingamon - 12-24-2020, 04:19 PM

RE: AS4 Hobbyists Radio - by RodB - 12-24-2020, 06:27 PM

RE: AS4 Hobbyists Radio - by Daniel Bingamon - 12-24-2020, 07:48 PM

RE: AS4 Hobbyists Radio - by Radioroslyn - 12-24-2020, 09:22 PM

RE: AS4 Hobbyists Radio - by vinzer - 12-24-2020, 09:28 PM

RE: AS4 Hobbyists Radio - by Daniel Bingamon - 12-30-2020, 11:24 PM

RE: AS4 Hobbyists Radio - by Arran - 12-31-2020, 04:48 AM

RE: AS4 Hobbyists Radio - by Daniel Bingamon - 01-15-2021, 08:37 PM

RE: AS4 Hobbyists Radio - by Daniel Bingamon - 01-17-2021, 05:12 PM

RE: AS4 Hobbyists Radio - by Daniel Bingamon - 01-24-2021, 03:49 PM

RE: AS4 Hobbyists Radio - by Daniel Bingamon - 05-16-2021, 10:50 AM

RE: AS4 Hobbyists Radio - by OZ4 - 05-16-2021, 01:21 PM

RE: AS4 Hobbyists Radio - by Daniel Bingamon - 09-19-2021, 01:48 PM

View a Printable Version

Users browsing this thread: 3 Guest(s)

Recent Posts
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio. This is a shame because this should be a good performer. 2A...captainclock1988 — 03:43 PM
Philco 42-390, code 121 speaker
Using a 5W 1.5k ceramic resistor in place of the field coil and using a 4 ohm PM speaker, I was able to bring the radi...Stevelog — 02:57 PM

Who's Online

There are currently 4424 online users. [Complete List]
» 2 Member(s) | 4422 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me