1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco PT 29 line resistor
Philcofan
Junior Member
**
Posts: 36
Threads: 14
Joined: Apr 2012
City: Greenville, NY
#5

01-01-2021, 04:21 PM
So is it two separate resistors? Where do I get them? How do I connect them? Sorry this type of resistor is new to me.


Thanks
Chris
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco PT 29 line resistor - by Philcofan - 01-01-2021, 03:26 PM
RE: Philco PT 29 line resistor - by Radioroslyn - 01-01-2021, 03:42 PM
RE: Philco PT 29 line resistor - by Philcofan - 01-01-2021, 03:52 PM
RE: Philco PT 29 line resistor - by Radioroslyn - 01-01-2021, 04:14 PM
RE: Philco PT 29 line resistor - by Philcofan - 01-01-2021, 04:21 PM
RE: Philco PT 29 line resistor - by Radioroslyn - 01-01-2021, 04:32 PM
RE: Philco PT 29 line resistor - by Philcofan - 01-01-2021, 04:53 PM
RE: Philco PT 29 line resistor - by Radioroslyn - 01-01-2021, 05:09 PM
RE: Philco PT 29 line resistor - by Bill Bacco - 01-01-2021, 09:38 PM
RE: Philco PT 29 line resistor - by morzh - 01-01-2021, 11:26 PM
RE: Philco PT 29 line resistor - by RodB - 01-02-2021, 10:20 AM
RE: Philco PT 29 line resistor - by Philcofan - 01-20-2021, 05:15 PM
RE: Philco PT 29 line resistor - by Radioroslyn - 01-20-2021, 05:22 PM
RE: Philco PT 29 line resistor - by Philcofan - 01-21-2021, 09:17 PM
RE: Philco PT 29 line resistor - by morzh - 01-21-2021, 09:39 PM
RE: Philco PT 29 line resistor - by Bill Bacco - 01-21-2021, 11:12 PM
RE: Philco PT 29 line resistor - by Philcofan - 01-22-2021, 07:02 PM
RE: Philco PT 29 line resistor - by Bill Bacco - 01-22-2021, 09:51 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration