1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Model 80 jr resistors getting hot
Xolo100
Junior Member
**
Posts: 14
Threads: 1
Joined: Nov 2020
City: GLEN RIDGE State, Province, Country: NJ
#12

01-02-2021, 10:53 PM
I'm getting 165 volts across the 16K resistor. I'm getting 250 volts on the plate voltage for the detector oscillator 36 tube. I will make more measurements tomorrow evening when I get back from work. Sorry for the confusion.
Find
« Next Oldest | Next Newest »


Messages In This Thread
Model 80 jr resistors getting hot - by Xolo100 - 01-02-2021, 12:43 PM
RE: Model 80 jr resistors getting hot - by morzh - 01-02-2021, 01:45 PM
RE: Model 80 jr resistors getting hot - by morzh - 01-02-2021, 05:33 PM
RE: Model 80 jr resistors getting hot - by morzh - 01-02-2021, 07:14 PM
RE: Model 80 jr resistors getting hot - by morzh - 01-02-2021, 07:22 PM
RE: Model 80 jr resistors getting hot - by morzh - 01-02-2021, 09:43 PM
RE: Model 80 jr resistors getting hot - by n1ps - 01-02-2021, 10:35 PM
RE: Model 80 jr resistors getting hot - by Xolo100 - 01-02-2021, 10:53 PM
RE: Model 80 jr resistors getting hot - by RodB - 01-04-2021, 10:38 AM
RE: Model 80 jr resistors getting hot - by RodB - 01-04-2021, 07:30 PM
RE: Model 80 jr resistors getting hot - by morzh - 01-04-2021, 09:42 PM
RE: Model 80 jr resistors getting hot - by morzh - 01-04-2021, 11:33 PM
RE: Model 80 jr resistors getting hot - by morzh - 04-23-2021, 10:39 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM

[-]
Who's Online
There are currently 4453 online users. [Complete List]
» 4 Member(s) | 4449 Guest(s)
AvatarAvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration