91-221 coils

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

91-221 coils

BWeismann
Junior Member

Posts: 6
Threads: 2
Joined: Dec 2020
City: Valparaiso State, Province, Country: Indiana

01-20-2021, 11:27 AM

Thanks, Terry.
I've got a few more questions.
1. Should it be bare copper wire or enameled, etc.
2. Do you know of a good source for said wire?
3. Any tips as to removing that bobbin without damaging/distorting the main tube and its coils?

As you likely know, it's riveted to a piece of material that is then fixated in 2 slots at the end of the tube. Initial inclination is to distort the tube and then pull the tabs out with a needle nose. Will I be jeopardizng the other coils (from 1932) with such a move? What's a safe way to get it done?

Find

« Next Oldest | Next Newest »

Messages In This Thread

91-221 coils - by BWeismann - 01-19-2021, 09:54 PM

RE: 91-221 coils - by Radioroslyn - 01-20-2021, 12:02 AM

RE: 91-221 coils - by BWeismann - 01-20-2021, 11:27 AM

RE: 91-221 coils - by Radioroslyn - 01-20-2021, 01:35 PM

RE: 91-221 coils - by BWeismann - 01-20-2021, 01:58 PM

RE: 91-221 coils - by Phlogiston - 01-20-2021, 02:41 PM

RE: 91-221 coils - by BWeismann - 01-20-2021, 03:28 PM

RE: 91-221 coils - by Phlogiston - 01-20-2021, 03:41 PM

RE: 91-221 coils - by Radioroslyn - 01-20-2021, 04:19 PM

RE: 91-221 coils - by BWeismann - 01-21-2021, 08:28 PM

View a Printable Version

Users browsing this thread: 3 Guest(s)

Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

Who's Online

There are currently 5054 online users. [Complete List]
» 3 Member(s) | 5051 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me