37-84 code 122 low B+

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

37-84 code 122 low B+

Radioroslyn
Phorum Expert

Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa

01-20-2021, 11:07 PM

Obtw I'll mention in passing it's very easy to wire #20 backwards so the that the .015 is connected to the plate of the detector and ground, and the .001 ends up being the couple cap. What this amounts to is that the audio sounds weak and muffled. Have done it before...

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry

Find

« Next Oldest | Next Newest »

Messages In This Thread

37-84 code 122 low B+ - by govee - 01-20-2021, 08:19 PM

RE: 37-84 code 122 low B+ - by Radioroslyn - 01-20-2021, 08:44 PM

RE: 37-84 code 122 low B+ - by govee - 01-20-2021, 10:35 PM

RE: 37-84 code 122 low B+ - by Radioroslyn - 01-20-2021, 10:53 PM

RE: 37-84 code 122 low B+ - by Radioroslyn - 01-20-2021, 11:07 PM

RE: 37-84 code 122 low B+ - by govee - 01-20-2021, 11:45 PM

RE: 37-84 code 122 low B+ - by Radioroslyn - 01-21-2021, 01:21 PM

RE: 37-84 code 122 low B+ - by govee - 01-21-2021, 02:54 PM

RE: 37-84 code 122 low B+ - by RodB - 01-21-2021, 05:08 PM

View a Printable Version

Users browsing this thread: 4 Guest(s)

Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

Who's Online

There are currently 5162 online users. [Complete List]
» 2 Member(s) | 5160 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me