1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco PT 29 line resistor
Bill Bacco
Member
***
Posts: 94
Threads: 9
Joined: Feb 2013
City: Monroeville, PA
#16

01-21-2021, 11:12 PM
Sounds like you have a short some where. Did you measure the line current? Heaters should be drawing about 150ma. Not sure what you mean by ground lug of 35Z3. I don't believe any of these resistors should be grounded. Do you mean the plate? Have you tested the tubes?
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco PT 29 line resistor - by Philcofan - 01-01-2021, 03:26 PM
RE: Philco PT 29 line resistor - by Radioroslyn - 01-01-2021, 03:42 PM
RE: Philco PT 29 line resistor - by Philcofan - 01-01-2021, 03:52 PM
RE: Philco PT 29 line resistor - by Radioroslyn - 01-01-2021, 04:14 PM
RE: Philco PT 29 line resistor - by Philcofan - 01-01-2021, 04:21 PM
RE: Philco PT 29 line resistor - by Radioroslyn - 01-01-2021, 04:32 PM
RE: Philco PT 29 line resistor - by Philcofan - 01-01-2021, 04:53 PM
RE: Philco PT 29 line resistor - by Radioroslyn - 01-01-2021, 05:09 PM
RE: Philco PT 29 line resistor - by Bill Bacco - 01-01-2021, 09:38 PM
RE: Philco PT 29 line resistor - by morzh - 01-01-2021, 11:26 PM
RE: Philco PT 29 line resistor - by RodB - 01-02-2021, 10:20 AM
RE: Philco PT 29 line resistor - by Philcofan - 01-20-2021, 05:15 PM
RE: Philco PT 29 line resistor - by Radioroslyn - 01-20-2021, 05:22 PM
RE: Philco PT 29 line resistor - by Philcofan - 01-21-2021, 09:17 PM
RE: Philco PT 29 line resistor - by morzh - 01-21-2021, 09:39 PM
RE: Philco PT 29 line resistor - by Bill Bacco - 01-21-2021, 11:12 PM
RE: Philco PT 29 line resistor - by Philcofan - 01-22-2021, 07:02 PM
RE: Philco PT 29 line resistor - by Bill Bacco - 01-22-2021, 09:51 PM



Users browsing this thread: 5 Guest(s)
[-]
Recent Posts
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM

[-]
Who's Online
There are currently 5529 online users. [Complete List]
» 2 Member(s) | 5527 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration