1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
[split] My 47-1230 Restoration
rstokes58
Junior Member
**
Posts: 22
Threads: 4
Joined: Dec 2020
City: westhampton State, Province, Country: New York
#6

01-24-2021, 12:09 PM
thanks for the advice

Im thinking the latter then replace the caps systematically. Any help or advice would be welcome.

I would do it all at once.

Has anyone compiled a list of the paper /wax caps for this radio?  Im assuming 500v rating?  electrolyte ? 

Thanks
Find
« Next Oldest | Next Newest »


Messages In This Thread
[split] My 47-1230 Restoration - by rstokes58 - 01-22-2021, 10:49 AM
RE: [split] My 47-1230 Restoration - by Arran - 01-22-2021, 10:35 PM
RE: [split] My 47-1230 Restoration - by rstokes58 - 01-23-2021, 03:49 PM
RE: [split] My 47-1230 Restoration - by rstokes58 - 01-24-2021, 12:09 PM
RE: [split] My 47-1230 Restoration - by RodB - 01-24-2021, 12:50 PM
RE: [split] My 47-1230 Restoration - by rstokes58 - 01-30-2021, 05:47 PM
RE: [split] My 47-1230 Restoration - by rstokes58 - 01-30-2021, 08:15 PM
RE: [split] My 47-1230 Restoration - by rstokes58 - 01-30-2021, 08:28 PM
RE: [split] My 47-1230 Restoration - by rstokes58 - 02-01-2021, 09:46 PM
RE: [split] My 47-1230 Restoration - by Arran - 02-03-2021, 02:43 AM



Users browsing this thread: 7 Guest(s)
[-]
Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

[-]
Who's Online
There are currently 5171 online users. [Complete List]
» 2 Member(s) | 5169 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration