Phico 38-40 antenna coil

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Phico 38-40 antenna coil

GaryK
Junior Member

Posts: 7
Threads: 1
Joined: Jan 2021
City: LOTT State, Province, Country: TX

01-27-2021, 12:31 PM

The coil #5 looks to be grounded through coil #6 at two points, through the 120K resistor #8 and through trimmer #7A and cap #9. My band selector is out of circuit so A2 and A3 are not there. I have a parts chassis from a 38-14 comming, i will try to use the band selector from that and try to get this thing connected properly. Thanks.

Find

« Next Oldest | Next Newest »

Messages In This Thread

Phico 38-40 antenna coil - by GaryK - 01-22-2021, 08:32 PM

RE: Phico 38-40 antenna coil - by rfeenstra - 01-23-2021, 01:36 AM

RE: Phico 38-40 antenna coil - by GaryK - 01-23-2021, 02:41 PM

RE: Phico 38-40 antenna coil - by radio1 - 01-26-2021, 10:46 PM

RE: Phico 38-40 antenna coil - by rfeenstra - 01-26-2021, 11:46 PM

RE: Phico 38-40 antenna coil - by GaryK - 01-27-2021, 12:31 PM

RE: Phico 38-40 antenna coil - by GaryK - 01-27-2021, 12:41 PM

RE: Phico 38-40 antenna coil - by rfeenstra - 01-27-2021, 01:25 PM

RE: Phico 38-40 antenna coil - by 462ron - 01-28-2021, 08:47 AM

RE: Phico 38-40 antenna coil - by GaryK - 01-28-2021, 10:49 AM

RE: Phico 38-40 antenna coil - by radio1 - 01-28-2021, 07:56 PM

RE: Phico 38-40 antenna coil - by GaryK - 01-28-2021, 11:31 PM

RE: Phico 38-40 antenna coil - by GaryK - 02-10-2021, 03:26 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me