1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Phico 38-40 antenna coil
GaryK
Junior Member
**
Posts: 7
Threads: 1
Joined: Jan 2021
City: LOTT State, Province, Country: TX
#7

01-27-2021, 12:41 PM
Yes, point 4 of my antenna coil is going through a 1meg resistor #17 to the plate of 6J5. I measure about -1.5 volt to -2.5 at the plate of 6J5. The connection A2 and A3 are not there beceause the band selector is out of circuit. So could i use a jumper wire to close that connection? I have a parts chassis comming from E-bay, a 38-14 and it looks like it may have a band selector i could use and maybe the range 2 antenna coil as well. Thanks.
Find
« Next Oldest | Next Newest »


Messages In This Thread
Phico 38-40 antenna coil - by GaryK - 01-22-2021, 08:32 PM
RE: Phico 38-40 antenna coil - by rfeenstra - 01-23-2021, 01:36 AM
RE: Phico 38-40 antenna coil - by GaryK - 01-23-2021, 02:41 PM
RE: Phico 38-40 antenna coil - by radio1 - 01-26-2021, 10:46 PM
RE: Phico 38-40 antenna coil - by rfeenstra - 01-26-2021, 11:46 PM
RE: Phico 38-40 antenna coil - by GaryK - 01-27-2021, 12:31 PM
RE: Phico 38-40 antenna coil - by GaryK - 01-27-2021, 12:41 PM
RE: Phico 38-40 antenna coil - by rfeenstra - 01-27-2021, 01:25 PM
RE: Phico 38-40 antenna coil - by 462ron - 01-28-2021, 08:47 AM
RE: Phico 38-40 antenna coil - by GaryK - 01-28-2021, 10:49 AM
RE: Phico 38-40 antenna coil - by radio1 - 01-28-2021, 07:56 PM
RE: Phico 38-40 antenna coil - by GaryK - 01-28-2021, 11:31 PM
RE: Phico 38-40 antenna coil - by GaryK - 02-10-2021, 03:26 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

[-]
Who's Online
There are currently 5112 online users. [Complete List]
» 2 Member(s) | 5110 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration