Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Scott SLRM
#21

Not bad for custom made new manufacture twist-lok cans, no, not at all.

My Fisher TA-600 has Hayseed Hamfest twist-loks in it. They are good people. Icon_thumbup

--
Ron Ramirez
Ferdinand IN


Messages In This Thread
Scott SLRM - by mikethedruid - 01-31-2021, 04:00 PM
RE: Scott SLRM - by rfeenstra - 01-31-2021, 09:49 PM
RE: Scott SLRM - by mikethedruid - 02-02-2021, 05:43 PM
RE: Scott SLRM - by rfeenstra - 02-02-2021, 06:30 PM
RE: Scott SLRM - by rfeenstra - 02-02-2021, 06:36 PM
RE: Scott SLRM - by mikethedruid - 02-02-2021, 07:03 PM
RE: Scott SLRM - by Paul Philco322 - 02-02-2021, 07:09 PM
RE: Scott SLRM - by mikethedruid - 02-02-2021, 09:14 PM
RE: Scott SLRM - by rfeenstra - 02-03-2021, 12:00 AM
RE: Scott SLRM - by rfeenstra - 02-03-2021, 12:27 AM
RE: Scott SLRM - by mikethedruid - 02-03-2021, 12:48 AM
RE: Scott SLRM - by mikethedruid - 02-03-2021, 01:24 AM
RE: Scott SLRM - by mikethedruid - 02-03-2021, 02:23 AM
RE: Scott SLRM - by rfeenstra - 02-03-2021, 10:45 AM
RE: Scott SLRM - by mikethedruid - 02-04-2021, 05:45 PM
RE: Scott SLRM - by Eliot Ness - 02-04-2021, 07:11 PM
RE: Scott SLRM - by mikethedruid - 02-05-2021, 11:31 PM
RE: Scott SLRM - by morzh - 02-06-2021, 12:33 AM
RE: Scott SLRM - by rfeenstra - 02-06-2021, 11:28 AM
RE: Scott SLRM - by mikethedruid - 02-06-2021, 01:45 PM
RE: Scott SLRM - by Ron Ramirez - 02-06-2021, 01:56 PM
RE: Scott SLRM - by mikethedruid - 02-06-2021, 06:57 PM
RE: Scott SLRM - by mikethedruid - 02-08-2021, 04:27 PM
RE: Scott SLRM - by mikethedruid - 02-08-2021, 08:24 PM
RE: Scott SLRM - by mikethedruid - 02-08-2021, 11:03 PM
RE: Scott SLRM - by rfeenstra - 02-08-2021, 11:51 PM
RE: Scott SLRM - by mikethedruid - 02-10-2021, 08:54 PM
RE: Scott SLRM - by mikethedruid - 02-11-2021, 08:22 PM
RE: Scott SLRM - by mikethedruid - 02-18-2021, 08:27 PM
RE: Scott SLRM - by mikethedruid - 02-24-2021, 10:52 PM
RE: Scott SLRM - by Eliot Ness - 02-25-2021, 11:19 AM
RE: Scott SLRM - by mikethedruid - 02-25-2021, 11:14 PM



Users browsing this thread: 4 Guest(s)
[-]
Recent Posts
Bakelite crack repair - what is best epoxy?
Thanks everyone. I appreciate you sharing your experience and looks like I'll work with the 24 hr two part clear epoxy....de371 — 10:25 PM
Jackson 665 j2 schematic request
Without a schematic its going to be hard tracing the wire wound spool resistors.daveone23 — 05:21 PM
Jackson 665 j2 schematic request
Looking for a schematic for the 665 j2 multimeter.daveone23 — 04:42 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
>>I'll write to the Henry Ford. I heard, his secretary answers his mail, not he himself.morzh — 12:15 PM
Philco 48-200 alignment questions
Just checked the power cord and I did in fact wire it so the hot side (small prong) goes to the switch.transitony — 11:52 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
Thanks for the suggestions.  I'll write to the Henry Ford.   That would certainly make sense since by the time this prod...jeibner — 11:49 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
For what it's worth, the Henry Ford Museum and Greenfield Village in Dearborn, Michigan may be an option. The obvious ...GarySP — 11:39 AM
Help with Readrite 410 tube tester
Mike and I just had a short discussion yesterday about this very subject. So often it's the connections. Ya gotta have t...RodB — 10:08 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
We have a regional museum here in the Twin Cities called The Pavek Museum. They have an extensive collection of communic...RodB — 09:30 AM
Philco 89B code 123 newbie
I did some nosing around and found that the original caps were 4 3/4" long x 1 5/16" in dia. Guess what 1"...Radioroslyn — 09:28 AM

[-]
Who's Online
There are currently 5341 online users. [Complete List]
» 1 Member(s) | 5340 Guest(s)
Avatar

>