1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Model 60 stain color
Arran
Phorum Expert
*****
Posts: 4,639
Threads: 51
Joined: Sep 2008
City: Sandwick, BC, CA
#17

02-06-2021, 07:22 PM
I heard that the German sets often used polyester resin, kind of like fiberglass gel coat . In any event I think it's catalyzed, whatever the stuff is,  and hard to get off. I wonder if scuffing up the surface of either would make it easier to strip off, with something like steel wool or a finer grit of sandpaper, that trick works on stripping off powder coating that has gone bad.
Regards
Arran
Find
« Next Oldest | Next Newest »


Messages In This Thread
Model 60 stain color - by 45philcodon - 02-05-2021, 02:57 PM
RE: Model 60 stain color - by Arran - 02-05-2021, 05:16 PM
RE: Model 60 stain color - by 45philcodon - 02-05-2021, 06:07 PM
RE: Model 60 stain color - by Ron Ramirez - 02-05-2021, 06:49 PM
RE: Model 60 stain color - by Phlogiston - 02-05-2021, 06:53 PM
RE: Model 60 stain color - by 45philcodon - 02-05-2021, 06:56 PM
RE: Model 60 stain color - by 45philcodon - 02-05-2021, 06:57 PM
RE: Model 60 stain color - by radiorich - 02-05-2021, 11:23 PM
RE: Model 60 stain color - by John Bartley - 02-06-2021, 08:24 AM
RE: Model 60 stain color - by Ron Ramirez - 02-06-2021, 10:23 AM
RE: Model 60 stain color - by John Bartley - 02-06-2021, 10:43 AM
RE: Model 60 stain color - by Ron Ramirez - 02-06-2021, 11:04 AM
RE: Model 60 stain color - by Phlogiston - 02-06-2021, 12:18 PM
RE: Model 60 stain color - by 45philcodon - 02-06-2021, 12:59 PM
RE: Model 60 stain color - by Phlogiston - 02-06-2021, 01:08 PM
RE: Model 60 stain color - by Ron Ramirez - 02-06-2021, 01:48 PM
RE: Model 60 stain color - by Arran - 02-06-2021, 07:22 PM
RE: Model 60 stain color - by John Bartley - 02-07-2021, 08:07 AM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM

[-]
Who's Online
There are currently 4110 online users. [Complete List]
» 1 Member(s) | 4109 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration