First Resto - Philco 60B

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

First Resto - Philco 60B

LDel
Junior Member

Posts: 21
Threads: 1
Joined: Feb 2021
City: La Baie State, Province, Country: Québec

#21

02-08-2021, 07:14 PM

Mikethedruid - many thanks for your advice. Yes, I have a tube tester, and before I do any work on a set, I test the tubes. This 60B really has me stymied. I've been VERY careful with each step i.e. re-stuffing the condenser blocks, replacing out of tolerance resisters, replacing decrepit wiring etc. and something just isn't right. I've tried to locate a defective part/stage with the signal tracing method to no avail. Obviously, I have missed something or done something wrong, but I've never experienced the symptoms that this set is giving. I'm stubborn as a mule, and I'm not going to give up, but I must admit to feeling frustrated.

Find

« Next Oldest | Next Newest »

Messages In This Thread

First Resto - Philco 60B - by LDel - 02-06-2021, 02:39 PM

RE: First Resto - Philco 60B - by Ron Ramirez - 02-06-2021, 02:53 PM

RE: First Resto - Philco 60B - by Radioroslyn - 02-06-2021, 06:58 PM

RE: First Resto - Philco 60B - by LDel - 02-06-2021, 07:35 PM

RE: First Resto - Philco 60B - by Radioroslyn - 02-06-2021, 11:45 PM

RE: First Resto - Philco 60B - by fenbach - 02-07-2021, 01:00 AM

RE: First Resto - Philco 60B - by LDel - 02-07-2021, 08:28 AM

RE: First Resto - Philco 60B - by LDel - 02-07-2021, 08:29 AM

RE: First Resto - Philco 60B - by Radioroslyn - 02-07-2021, 11:19 AM

RE: First Resto - Philco 60B - by LDel - 02-07-2021, 12:57 PM

RE: First Resto - Philco 60B - by LDel - 02-07-2021, 10:31 PM

RE: First Resto - Philco 60B - by Radioroslyn - 02-07-2021, 11:47 PM

RE: First Resto - Philco 60B - by mikethedruid - 02-07-2021, 11:56 PM

RE: First Resto - Philco 60B - by LDel - 02-08-2021, 01:41 PM

RE: First Resto - Philco 60B - by LDel - 02-08-2021, 02:04 PM

RE: First Resto - Philco 60B - by mikethedruid - 02-08-2021, 02:04 PM

RE: First Resto - Philco 60B - by LDel - 02-08-2021, 02:09 PM

RE: First Resto - Philco 60B - by LDel - 02-08-2021, 03:50 PM

RE: First Resto - Philco 60B - by Radioroslyn - 02-08-2021, 05:21 PM

RE: First Resto - Philco 60B - by LDel - 02-08-2021, 06:07 PM

RE: First Resto - Philco 60B - by LDel - 02-08-2021, 07:14 PM

RE: First Resto - Philco 60B - by LDel - 02-11-2021, 04:09 PM

RE: First Resto - Philco 60B - by Radioroslyn - 02-11-2021, 05:37 PM

RE: First Resto - Philco 60B - by LDel - 02-16-2021, 10:45 AM

RE: First Resto - Philco 60B - by fenbach - 02-16-2021, 03:59 PM

RE: First Resto - Philco 60B - by LDel - 02-16-2021, 04:44 PM

RE: First Resto - Philco 60B - by Radioroslyn - 02-16-2021, 05:02 PM

RE: First Resto - Philco 60B - by LDel - 02-16-2021, 05:37 PM

RE: First Resto - Philco 60B - by LDel - 02-24-2021, 04:33 PM

RE: First Resto - Philco 60B - by RodB - 02-24-2021, 05:42 PM

RE: First Resto - Philco 60B - by LDel - 02-24-2021, 05:47 PM

RE: First Resto - Philco 60B - by LDel - 03-06-2021, 04:46 PM

RE: First Resto - Philco 60B - by Radioroslyn - 03-06-2021, 05:52 PM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM

Who's Online

There are currently 4449 online users. [Complete List]
» 4 Member(s) | 4445 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me