1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
37-60 alignment problem
Phlogiston
Radio-Fixer-Upper
*****
Posts: 2,118
Threads: 112
Joined: Jun 2010
City: Medford OR (OR what?)
#2

02-15-2021, 02:48 PM
Oh - boy. Check for threads on Philco Coils, the failures and those that are detuned by moisture and age.

I would start by ignoring the direction and setting my signal generator to the receive freq and see what happens. After you figure it out, then, you can deal with images.

Russ
"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
Website Find
« Next Oldest | Next Newest »


Messages In This Thread
37-60 alignment problem - by madsowry - 02-15-2021, 02:40 PM
RE: 37-60 alignment problem - by Phlogiston - 02-15-2021, 02:48 PM
RE: 37-60 alignment problem - by madsowry - 02-15-2021, 02:54 PM
RE: 37-60 alignment problem - by Radioroslyn - 02-15-2021, 07:06 PM
RE: 37-60 alignment problem - by madsowry - 02-15-2021, 08:11 PM
RE: 37-60 alignment problem - by morzh - 02-15-2021, 10:56 PM
RE: 37-60 alignment problem - by Radioroslyn - 02-15-2021, 11:35 PM
RE: 37-60 alignment problem - by madsowry - 02-17-2021, 04:08 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

[-]
Who's Online
There are currently 5149 online users. [Complete List]
» 2 Member(s) | 5147 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration