Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Is any hum at all tolerable?
#3

It's sort of like those who just get into vinyl records, they cannot accept the background noise. With a good system though, it will make the goose bumps rise. I read in an old radio publication that all radios hum to a certain extent, but if too much when installed in the cab it could indicate a problem somewhere. Most good tube radios I have listened to have very little hum, it's there, not that bad. Might try lead dress and movement to minimize. Some tubes can hum, and they test good. It could be in your house wiring or other interference, many things can cause it. The AA5's I have had listened to had virtually no hum. Alignment can dial in hum, been there, seen it first hand. If everything you have is unacceptable, something is wrong somewhere, not normal.


Messages In This Thread
Is any hum at all tolerable? - by lasurveyor - 02-20-2021, 08:38 PM
RE: Is any hum at all tolerable? - by David - 02-20-2021, 08:50 PM
RE: Is any hum at all tolerable? - by radio1 - 02-20-2021, 09:12 PM
RE: Is any hum at all tolerable? - by lasurveyor - 02-20-2021, 09:16 PM
RE: Is any hum at all tolerable? - by gregb - 02-20-2021, 09:25 PM
RE: Is any hum at all tolerable? - by lasurveyor - 02-20-2021, 10:02 PM
RE: Is any hum at all tolerable? - by Radioroslyn - 02-20-2021, 10:25 PM
RE: Is any hum at all tolerable? - by radiorich - 02-20-2021, 11:03 PM
RE: Is any hum at all tolerable? - by RodB - 02-21-2021, 09:23 AM
RE: Is any hum at all tolerable? - by lasurveyor - 02-21-2021, 02:30 PM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

[-]
Who's Online
There are currently 5137 online users. [Complete List]
» 1 Member(s) | 5136 Guest(s)
Avatar

>