1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
16B#2 Chassis
Radioroslyn
Phorum Expert
*****
Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#6

02-25-2021, 03:31 PM
Did a trial run w/the JB Weld just to see how it works. This is the Quick set stuff. I found the that it doesn't really set in 6 mins more like 20 mins. Gets hard under a 60w bulb after about 12hrs, probably not full strength but for this application it's definitely strong enough. As of now I've had it about 8" away from 60w lamp to keep it warm for the last 20hrs. Seems great.

I was kinda dreading it that I was going to misaligned the contacts and have a real mess on my hands...


Attached Files Image(s)
   
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
(This post was last modified: 02-25-2021, 06:56 PM by Radioroslyn.)
Find
« Next Oldest | Next Newest »


Messages In This Thread
16B#2 Chassis - by Radioroslyn - 11-02-2020, 03:44 PM
RE: 16B#2 Chassis - by EdHolland - 11-04-2020, 04:26 PM
RE: 16B#2 Chassis - by Radioroslyn - 12-05-2020, 09:00 PM
RE: 16B#2 Chassis - by Radioroslyn - 02-18-2021, 10:33 PM
RE: 16B#2 Chassis - by Radioroslyn - 02-19-2021, 01:19 PM
RE: 16B#2 Chassis - by Radioroslyn - 02-25-2021, 03:31 PM
RE: 16B#2 Chassis - by Radioroslyn - 02-25-2021, 08:45 PM
RE: 16B#2 Chassis - by Arran - 02-25-2021, 09:13 PM
RE: 16B#2 Chassis - by Radioroslyn - 02-26-2021, 11:47 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 4691 online users. [Complete List]
» 2 Member(s) | 4689 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration