Philco 20 voltages

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Philco 20 voltages

Bill Bacco
Member

Posts: 94
Threads: 9
Joined: Feb 2013
City: Monroeville, PA

#19

02-28-2021, 09:56 AM

Also don't forget to verify your power supply voltages are correct. The numbers you have for the 71A plate seem kind of low. This could be related to where you were measuring from (ground vs. point B). It would be interesting to see what you have on each side of coil #27. Maybe rfeenstra could do the same measurement.

Bill

Find

« Next Oldest | Next Newest »

Messages In This Thread

Philco 20 voltages - by Patrick - 02-26-2021, 11:41 AM

RE: Philco 20 voltages - by Radioroslyn - 02-26-2021, 01:22 PM

RE: Philco 20 voltages - by Patrick - 02-27-2021, 08:29 AM

RE: Philco 20 voltages - by Radioroslyn - 02-27-2021, 09:58 AM

RE: Philco 20 voltages - by RodB - 02-27-2021, 11:20 AM

RE: Philco 20 voltages - by 462ron - 02-27-2021, 11:28 AM

RE: Philco 20 voltages - by rfeenstra - 02-27-2021, 01:20 PM

RE: Philco 20 voltages - by Radioroslyn - 02-27-2021, 01:34 PM

RE: Philco 20 voltages - by 462ron - 02-27-2021, 01:45 PM

RE: Philco 20 voltages - by Patrick - 02-27-2021, 03:38 PM

RE: Philco 20 voltages - by RodB - 02-27-2021, 08:25 PM

RE: Philco 20 voltages - by RodB - 02-27-2021, 09:14 PM

RE: Philco 20 voltages - by Patrick - 02-27-2021, 09:57 PM

RE: Philco 20 voltages - by radio1 - 02-27-2021, 10:11 PM

RE: Philco 20 voltages - by rfeenstra - 02-28-2021, 01:16 AM

RE: Philco 20 voltages - by Patrick - 02-28-2021, 06:46 AM

RE: Philco 20 voltages - by Radioroslyn - 02-28-2021, 07:41 AM

RE: Philco 20 voltages - by Radioroslyn - 02-28-2021, 09:46 AM

RE: Philco 20 voltages - by Bill Bacco - 02-28-2021, 09:56 AM

RE: Philco 20 voltages - by Patrick - 02-28-2021, 11:25 AM

RE: Philco 20 voltages - by Patrick - 02-28-2021, 11:32 AM

RE: Philco 20 voltages - by Patrick - 02-28-2021, 12:03 PM

RE: Philco 20 voltages - by OZ4 - 02-28-2021, 03:06 PM

RE: Philco 20 voltages - by radiohenry - 02-28-2021, 05:11 PM

RE: Philco 20 voltages - by Patrick - 02-28-2021, 05:17 PM

RE: Philco 20 voltages - by radiohenry - 02-28-2021, 05:23 PM

RE: Philco 20 voltages - by OZ4 - 02-28-2021, 10:11 PM

RE: Philco 20 voltages - by rfeenstra - 02-28-2021, 10:33 PM

RE: Philco 20 voltages - by OZ4 - 02-28-2021, 10:42 PM

RE: Philco 20 voltages - by rfeenstra - 02-28-2021, 11:49 PM

RE: Philco 20 voltages - by Patrick - 03-01-2021, 06:19 AM

RE: Philco 20 voltages - by Patrick - 03-14-2021, 09:22 PM

RE: Philco 20 voltages - by morzh - 03-14-2021, 10:47 PM

RE: Philco 20 voltages - by Patrick - 03-15-2021, 06:15 AM

View a Printable Version

Users browsing this thread: 6 Guest(s)

Recent Posts
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM

Who's Online

There are currently 4471 online users. [Complete List]
» 3 Member(s) | 4468 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me