1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 43 - Filter Choke
Masonparker
Junior Member
**
Posts: 47
Threads: 10
Joined: Nov 2020
City: CHESAPEAKE State, Province, Country: VA
#22

03-20-2021, 08:34 PM
Checked 57-60 as well as 62 & 64 all were in tolerance. I looked like 58 was possibly grounded. Power up the unit and when I touch the grid cap the radio would squeal then buzz. But after the radio was on for a few minutes it would go to a low buzz. I noticed that item 60 was real hot and measured the resistance at .860M. So what is causing the resistor (#60) to heat up
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Philco 43 - Filter Choke - by Masonparker - 02-13-2021, 06:16 PM
RE: Philco 43 - Filter Choke - by Radioroslyn - 02-13-2021, 06:43 PM
RE: Philco 43 - Filter Choke - by morzh - 02-13-2021, 09:07 PM
RE: Philco 43 - Filter Choke - by Masonparker - 02-21-2021, 08:08 PM
RE: Philco 43 - Filter Choke - by Radioroslyn - 02-21-2021, 08:49 PM
RE: Philco 43 - Filter Choke - by morzh - 02-21-2021, 10:43 PM
RE: Philco 43 - Filter Choke - by Masonparker - 02-22-2021, 09:14 PM
RE: Philco 43 - Filter Choke - by morzh - 02-22-2021, 10:06 PM
RE: Philco 43 - Filter Choke - by Masonparker - 02-22-2021, 10:12 PM
RE: Philco 43 - Filter Choke - by Masonparker - 02-22-2021, 10:15 PM
RE: Philco 43 - Filter Choke - by Masonparker - 02-22-2021, 10:59 PM
RE: Philco 43 - Filter Choke - by morzh - 02-22-2021, 11:22 PM
RE: Philco 43 - Filter Choke - by Masonparker - 02-23-2021, 07:58 PM
RE: Philco 43 - Filter Choke - by Radioroslyn - 02-23-2021, 08:36 PM
RE: Philco 43 - Filter Choke - by Masonparker - 03-18-2021, 06:52 PM
RE: Philco 43 - Filter Choke - by Radioroslyn - 03-18-2021, 07:12 PM
RE: Philco 43 - Filter Choke - by Masonparker - 03-19-2021, 06:44 PM
RE: Philco 43 - Filter Choke - by Masonparker - 03-19-2021, 06:49 PM
RE: Philco 43 - Filter Choke - by Masonparker - 03-19-2021, 07:13 PM
RE: Philco 43 - Filter Choke - by Radioroslyn - 03-19-2021, 10:24 PM
RE: Philco 43 - Filter Choke - by morzh - 03-19-2021, 11:06 PM
RE: Philco 43 - Filter Choke - by Masonparker - 03-20-2021, 08:34 PM
RE: Philco 43 - Filter Choke - by morzh - 03-20-2021, 09:37 PM
RE: Philco 43 - Filter Choke - by Masonparker - 03-21-2021, 09:42 AM
RE: Philco 43 - Filter Choke - by morzh - 03-21-2021, 12:05 PM
RE: Philco 43 - Filter Choke - by Masonparker - 04-10-2021, 10:47 AM
RE: Philco 43 - Filter Choke - by Radioroslyn - 04-10-2021, 01:56 PM



Users browsing this thread: 4 Guest(s)
[-]
Recent Posts
Need Help to ID this radio 11 tube Philco
It is a 16B tombstone.morzh — 06:13 PM
Zenith H725
David - sorry, I reread your post and finally saw THD - now the % figures make sense. Thanks for explaining. The PSU...EdHolland — 06:06 PM
Need Help to ID this radio 11 tube Philco
Hi Everyone, New member but have been reading this for awhile for tips! Vaccum tubes were before my time so bear with ...Ken D. — 06:03 PM
My Philco 37-116 Restore
Thank you MrFixR55, I appreciate your comments very much. I do not detect much hum if any so I will be staying with the ...dconant — 05:15 PM
My Philco 37-116 Restore
Hi DConant Yes, you can replace chokes with resistors.  You do stand the risk of increased hum.  the solution is to inc...MrFixr55 — 04:23 PM
Zenith H725
1.7-3.9 %, a modified Sine wave inverter is around 25%. Most generators from big box stores run 10% at a 50% load. What ...David — 04:06 PM
My Philco 37-116 Restore
I am having a heck of a time doing the alignment on the AM band. I can't seem to dial in the 1500 KC oscillator. I can h...dconant — 03:35 PM
Zenith H725
David - I think I understand but what units are you discussing (Low of 1.7, high of 3.9)? Budget constraints for Ham ...EdHolland — 01:43 PM
My Philco 37-116 Restore
You're doing great. I wish I could be more involved, but my mind is right now preoccupied with the reason I am here in ...morzh — 12:21 PM
My Philco 37-116 Restore
Hope you guys are still with me. I have moved on to the alignment. I completed the IF alignment which was pretty muc...dconant — 10:47 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration