1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
RF but no IF on 610
Radioroslyn
Phorum Expert
*****
Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#2

04-02-2021, 12:00 PM
Do you mean hz or khz?
Would connect the generator to the grid cap of the 6A7 and set it for 460kc w/modulation. Adjust IF transformers for max signal. If there is no signal check voltages at the plate and screen of the 6A7 and 78.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
(This post was last modified: 04-02-2021, 12:01 PM by Radioroslyn.)
Find
« Next Oldest | Next Newest »


Messages In This Thread
RF but no IF on 610 - by Patrick - 04-02-2021, 10:20 AM
RE: RF but no IF on 610 - by Radioroslyn - 04-02-2021, 12:00 PM
RE: RF but no IF on 610 - by Patrick - 04-02-2021, 12:06 PM
RE: RF but no IF on 610 - by Radioroslyn - 04-02-2021, 12:07 PM
RE: RF but no IF on 610 - by Patrick - 04-02-2021, 12:10 PM
RE: RF but no IF on 610 - by Radioroslyn - 04-02-2021, 12:23 PM
RE: RF but no IF on 610 - by Patrick - 04-02-2021, 12:28 PM
RE: RF but no IF on 610 - by Radioroslyn - 04-02-2021, 12:38 PM
RE: RF but no IF on 610 - by Patrick - 04-02-2021, 01:17 PM
RE: RF but no IF on 610 - by morzh - 04-02-2021, 01:54 PM
RE: RF but no IF on 610 - by Patrick - 04-02-2021, 02:38 PM
RE: RF but no IF on 610 - by morzh - 04-02-2021, 02:42 PM
RE: RF but no IF on 610 - by Patrick - 04-02-2021, 02:58 PM
RE: RF but no IF on 610 - by morzh - 04-02-2021, 03:21 PM
RE: RF but no IF on 610 - by morzh - 04-02-2021, 03:31 PM
RE: RF but no IF on 610 - by Patrick - 04-02-2021, 04:23 PM
RE: RF but no IF on 610 - by Chas - 04-02-2021, 05:22 PM
RE: RF but no IF on 610 - by morzh - 04-02-2021, 07:15 PM
RE: RF but no IF on 610 - by Chas - 04-02-2021, 08:21 PM
RE: RF but no IF on 610 - by morzh - 04-02-2021, 08:24 PM
RE: RF but no IF on 610 - by Steve Davis - 04-02-2021, 08:47 PM
RE: RF but no IF on 610 - by morzh - 04-02-2021, 08:54 PM
RE: RF but no IF on 610 - by John Bartley - 04-02-2021, 09:17 PM
RE: RF but no IF on 610 - by Chas - 04-02-2021, 09:57 PM
RE: RF but no IF on 610 - by morzh - 04-02-2021, 10:04 PM
RE: RF but no IF on 610 - by mikethedruid - 04-02-2021, 10:07 PM
RE: RF but no IF on 610 - by Patrick - 04-02-2021, 10:14 PM
RE: RF but no IF on 610 - by morzh - 04-02-2021, 10:19 PM
RE: RF but no IF on 610 - by BrendaAnnD - 04-03-2021, 03:54 AM
RE: RF but no IF on 610 - by Patrick - 04-03-2021, 06:26 AM
RE: RF but no IF on 610 - by Paul Philco322 - 04-03-2021, 07:44 AM
RE: RF but no IF on 610 - by Patrick - 04-03-2021, 08:07 AM
RE: RF but no IF on 610 - by morzh - 04-03-2021, 10:29 AM
RE: RF but no IF on 610 - by morzh - 04-03-2021, 10:33 AM
RE: RF but no IF on 610 - by Patrick - 04-03-2021, 11:38 AM
RE: RF but no IF on 610 - by morzh - 04-03-2021, 01:02 PM
RE: RF but no IF on 610 - by Patrick - 04-03-2021, 02:58 PM
RE: RF but no IF on 610 - by mikethedruid - 04-03-2021, 05:03 PM
RE: RF but no IF on 610 - by morzh - 04-03-2021, 05:36 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM
Philco Predicta Siesta picture over time getting dimmer
I found that the wire insulation was burnt.  The fly back needs corona dope! Why would someone put that there?Platinumblonde36 — 01:09 AM

[-]
Who's Online
There are currently 4997 online users. [Complete List]
» 1 Member(s) | 4996 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration