Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

48-482
#20

in the absence of any adult supervision i pressed on. it would seem that with all the parts i replaced the i.f. will have to be adjusted 0ne more time. i ran the whole string and will need to do it again as the closer i got to the first i.f. the better it got until at the 1st if it peaked as it should. a revisit to step one and two brought success as well. ill finish it up on the morrow. i cant understand why they dont just have you START at the first i.f. like other radios. it would have saved a lot of grief. UNLESS there is a reason i dont quite understand????


Messages In This Thread
48-482 - by falcon123 - 02-09-2021, 02:33 AM
RE: 48-482 - by cparsons2391 - 02-09-2021, 08:55 AM
RE: 48-482 - by mikethedruid - 02-09-2021, 10:02 AM
RE: 48-482 - by morzh - 02-09-2021, 02:13 PM
RE: 48-482 - by falcon123 - 02-10-2021, 12:26 AM
RE: 48-482 - by morzh - 02-10-2021, 12:50 AM
RE: 48-482 - by falcon123 - 02-10-2021, 05:24 AM
48-482 - by falcon123 - 04-18-2021, 07:44 AM
RE: 48-482 - by mikethedruid - 04-18-2021, 11:46 AM
RE: 48-482 - by falcon123 - 04-19-2021, 02:29 AM
RE: 48-482 - by falcon123 - 04-19-2021, 08:52 AM
RE: 48-482 - by Ron Ramirez - 04-19-2021, 11:40 AM
RE: 48-482 - by falcon123 - 04-19-2021, 06:12 PM
RE: 48-482 - by falcon123 - 04-19-2021, 06:17 PM
RE: 48-482 - by falcon123 - 04-19-2021, 06:21 PM
philco 48-482 - by falcon123 - 05-09-2021, 01:56 AM
philco 48-482 index line - by falcon123 - 05-10-2021, 01:41 AM
RE: philco 48-482 index line - by falcon123 - 05-10-2021, 05:50 AM
48-482 fm i.f. alignment - by falcon123 - 05-12-2021, 12:57 AM
RE: 48-482 fm i.f. alignment - by falcon123 - 05-12-2021, 05:45 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Need to purchase some accessories for restoration of my Old Philco Radio
Hi Paulo, Welcome to the Philco Phorum. I can see why you want to find good reproduction parts. That is a bea...MrFixr55 — 11:10 PM
HiFi (Chifi) tube amp build - but my own design.
Tim, I have some bakelite sockets in my work shop that I can dig up. I believe quite a few are NOS. I will take photo...RodB — 10:03 PM
Philco 610B oscillator wiring
> The cathode as noted is wired directly to the ground side of the heater filament for that tube, not to the #17 and ...Radioroslyn — 08:12 PM
HiFi (Chifi) tube amp build - but my own design.
Tim; I noticed your post a little late, but I would take one of the junk sockets and try to break a chunk out of it wi...Arran — 08:07 PM
Need to purchase some accessories for restoration of my Old Philco Radio
Here is a list of resources found in our online library that you might find useful. Mike's Gobs of Knobs email addres...klondike98 — 01:46 PM
First Radio restoration
Hi Tubeman, Welcome to the Philco Phorum.  Phamily Phriendly Pfun with Phine Pholks Phull of Philco Phacts. (See a p...MrFixr55 — 12:33 PM
First Radio restoration
You could post in the WANTED ADs section here on the Phorum and see if anyone has an RF generator that they want to sell...klondike98 — 11:55 AM
Zenith H725
Good ideas, thank you Arrange and Rich. I have the adhesive aluminum foil already and can try that immediately. More ...EdHolland — 10:18 AM
Graphics for majestic 1050 dial glass.
Murf; I found this thread on the ARF, the first photo has a pretty good view of the dial glass. Regards ArranArran — 01:12 AM
Zenith H725
hello Ed, how about that speacial tape used for ducting it's like foil or how about thin piece of aluminum roof flash...radiorich — 12:19 AM

[-]
Who's Online
There are currently 1363 online users. [Complete List]
» 1 Member(s) | 1362 Guest(s)
Avatar

>